ADCMP606 datasheet(6/16 Pages) AD | Rail-to-Rail, Very Fast, 2.5 V to 5.5 V, Single-Supply CML Comparators

6 page

ADCMP606/ADCMP607

Preliminary Technical Data

Rev. PrA | Page 6 of 16

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

PIN 1

INDICATOR

VCCO

VCCI

VEE

9VEE

8LE/HYS

7SDN

TOP VIEW

(Not to Scale)

ADCMP607

Q 1

VEE 2

VP 3

VCCI/VCCO

ADCMP606

TOP VIEW

(Not to Scale)

Figure 3. ADCMP606 Pin Configuration

Figure 4. ADCMP607 Pin Configuration

Table 4. ADCMP606 (SC70-6) Pin Function Descriptions

Pin No.

Mnemonic

Description

Noninverting Output. Q is at logic high if the analog voltage at the noninverting input, VP, is greater

than the analog voltage at the inverting input, VN.

VEE

Negative Supply Voltage.

Noninverting Analog Input.

Inverting Analog Input.

V /V

CCI

CCO

Input Section Supply/Output Section Supply. Shared pin.

Inverting Output. Q is at logic low if the analog voltage at the noninverting input, VP, is greater than

the analog voltage at the inverting input, VN.

Table 5. ADCMP607 (LSCFP-12) Pin Function Descriptions

Pin No.

Mnemonic

Description

Output Section Supply.

CCO

VCCI

Input Section Supply.

VEE

Negative Supply Voltage.

Noninverting Analog Input.

VEE

Negative Supply Voltage.

Inverting Analog Input.

SDN

Shutdown. Drive this pin low to shut down the device.

LE/HYS

Latch/Hysteresis Control. Bias with resistor or current for hysteresis adjustment; drive low to latch.

VEE

Negative Supply Voltage.

Inverting Output. Q is at logic low if the analog voltage at the noninverting input, VP, is greater than the

analog voltage at the inverting input, VN, provided that the comparator is in compare mode.

VEE

Negative Supply Voltage.

Noninverting Output. Q is at logic high if the analog voltage at the noninverting input, VP, is greater than

the analog voltage at the inverting input, VN, provided that the comparator is in compare mode.

Heat Sink

Paddle

The metallic back surface of the package is electrically connected to V

. It can be left floating because

Pin 3, Pin 5, Pin 9, and Pin 11 provide adequate electrical connection. It can also be soldered to the

application board if improved thermal and/or mechanical stability is desired.

Número de Pieza	Descripción de Componentes	Html View	Fabricante
ADCMP600	Rail-to-Rail Very Fast 2.5 V to 5.5 V Single-Supply TTL/CMOS Comparators	1 2 3 4 5 More	Analog Devices
ADCMP604	Rail-to-Rail Very Fast 2.5 V to 5.5 V Single-Supply LVDS Comparators	1 2 3 4 5 More	Analog Devices
ADCMP603	Rail-to-Rail Very Fast 2.5 V to 5.5 V Single-Supply TTL/CMOS Comparator	1 2 3 4 5 More	Analog Devices
NCS2552	750 MHz Voltage Feedback Op Amp with Fast Enable Feature	1 2 3 4 5 More	ON Semiconductor
ZR285-25	PRECISION 2.5 VOLT MICROPOWER VOLTAGE REFERENCE	1 2 3 4	Zetex Semiconductors
FE3H	Super Fast Silicon Rectifiers	1 2	Diotec Semiconductor
ZR4040-25	PRECISION 2.5 VOLT MICROPOWER VOLTAGE REFERENCE	1 2 3 4	Zetex Semiconductors
FAN4113	1.2V 36MHz Low Power Rail-to-Rail Amplifier	1 2 3 4 5 More	Fairchild Semiconductor
AD7674	18-Bit 2.5 LSB INL 800 kSPS SAR ADC	1 2 3 4 5 More	Analog Devices
PI3A4626	3.0V SOTiny Single-Supply 0.4ohm SPST NO CMOS Analog Switch	1 2 3 4 5 More	Pericom Semiconductor Corporation

Número de Pieza relacionado

Enlace URL

Patrocinador de Alldatasheet