NB100LVEP56_06 datasheet(6/10 Pages) ONSEMI | 2.5V / 3.3V ECL DUAL Differential 2:1 Multiplexer

6 page

NB100LVEP56

http://onsemi.com

Table 8. AC CHARACTERISTICS VCC = 0 V; VEE = −2.375 V to −3.8 V or VCC = 2.375 V to 3.8 V; VEE = 0 V (Note 14)

Symbol

Characteristic

−40°C

25°C

85°C

Unit

Min

Typ

Max

Min

Typ

Max

Min

Typ

Max

VOUTPP Output Voltage Amplitude

fin v 1 GHz

(See Figure 4)

fin = 2 GHz

fin = 2.5 GHz

525

500

400

700

600

500

550

500

350

700

600

450

500

400

200

700

500

300

tPLH,

tPHL

Propagation Delay to Output Differential

D to Q, Q

SEL to Q, Q

COM_SEL to Q, Q

375

575

550

500

775

750

625

975

950

400

625

600

525

825

800

650

1025

1000

450

700

575

900

700

1100

tSkew

Pulse Skew (Note 15)

Within Device Input Skew (Note 16)

Within Device Output Skew (Note 17)

Device−to−Device Skew (Note 18)

200

tJITTER

RMS Random Clock Jitter (Note 19)

@ v1.0 GHz

@ v1.5 GHz

@ v2.0 GHz

@ v2.5 GHz

Peak−to−Peak Data Dependent Jitter (Note 20)

@ 0.5 GHz

@ 1.25 GHz

@ 2.488 GHz

0.269

0.306

0.250

0.339

4.1

32.2

30.8

0.4

0.8

0.307

0.303

0.305

0.895

4.6

22.6

27.2

0.4

0.5

2.0

0.371

0.391

0.722

2.443

4.4

24.4

0.5

0.6

1.2

7.7

VINPP

Input Voltage Swing (Differential Configuration)

(Note 21)

150

800

1200

150

800

1200

150

800

1200

Output Rise/Fall Times @ 50 MHz

Q, Q

(20% − 80%)

110

150

120

170

140

230

NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit

board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared

operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit

values are applied individually under normal operating conditions and not valid simultaneously.

14.Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC − 2.0 V. Input edge rates 150 ps (20% − 80%).

15.Pulse Skew |tPLH − tPHL|

16.Worst case difference between D0a and D0b (or between D1a or D1b), when both output come from same input.

17.Worst case difference between Q0 and Q1 outputs.

18.Skew is measured between outputs under identical transitions.

19.Additive RMS jitter with 50% Duty Cycle Clock Signal.

20.Additive Peak−to−Peak jitter with input NRZ data at PRBS 231−1.

21.Input voltage swing is a single−ended measurement operating in differential mode.

Figure 4. Output Voltage Amplitude (VOUTPP) vs.

Input Frequency (fin) at VCC = 2.5 V, 255C

INPUT FREQUENCY (GHz)

250

350

450

550

650

750

850

0.5

1.0

1.5

2.0

2.5

Q AMP (mV)

Número de Pieza	Descripción de Componentes	Html View	Fabricante
MC100LVEL56_06	3.3V ECL Dual Differential 2:1 Multiplexer	1 2 3 4 5 More	ON Semiconductor
MC10EP56_06	3.3V / 5V ECL Dual Differential 2:1 Multiplexer	1 2 3 4 5 More	ON Semiconductor
MC100EL56_06	5V ECL Dual Differential 2:1 Multiplexer	1 2 3 4 5 More	ON Semiconductor
MC100LVEL58_06	3.3V ECL 2:1 Multiplexer	1 2 3 4 5 More	ON Semiconductor
MC100LVEL59_06	3.3V ECL Triple 2:1 Multiplexer	1 2 3 4 5 More	ON Semiconductor
MC10EP29_06	3.3V / 5V ECL Dual Differential Data and Clock D Flip−Flop With Set and Reset	1 2 3 4 5 More	ON Semiconductor
MC100LVEP210_06	2.5V / 3.3V 1:5 Dual Differential ECL/PECL/HSTL Clock Driver	1 2 3 4 5 More	ON Semiconductor
MC100LVE210_06	3.3V ECL Dual 1:4 1:5 Differential Fanout Buffer	1 2 3 4 5 More	ON Semiconductor
MC10LVEP11_06	2.5V / 3.3V ECL 1:2 Differential Fanout Buffer	1 2 3 4 5 More	ON Semiconductor
MC10LVEP16_06	2.5V / 3.3V ECL Differential Receiver/Driver	1 2 3 4 5 More	ON Semiconductor

Número de Pieza relacionado

Enlace URL

Patrocinador de Alldatasheet