SP200_05 datasheet(6/16 Pages) SIPEX | +5V High-Speed RS-232 Transceivers with 0.1mF Capacitors

6 page

Date:05/26/2005

+5V High-Speed RS232 Transceivers

attain symmetrical

±10V power supplies.

Figure 3a shows the waveform found on the

positive side of capcitor C

2, and Figure 3b

shows the negative side of capcitor C

2. There is

a free–running oscillator that controls the four

phases of the voltage shifting. A description of

each phase follows.

Phase 1

— V

SS charge storage —During this phase of the

clock cycle, the positive side of capacitors C

and C

2 are initially charged to +5V. Cl

+ is then

switched to ground and the charge in C

– is

transferred to C

–. Since C

+ is connected to

+5V, the voltage potential across capacitor C

2 is

now 10V.

Phase 2

— V

SS transfer — Phase two of the clock con-

nects the negative terminal of C

2 to the VSS

storage capacitor and the positive terminal of C

to ground, and transfers the generated –l0V to

3. Simultaneously, the positive side of capaci-

tor C

1 is switched to +5V and the negative side

is connected to ground.

Phase 3

— V

DD charge storage — The third phase of the

clock is identical to the first phase — the charge

transferred in C

1 produces –5V in the negative

terminal of C

1, which is applied to the negative

side of capacitor C

2. Since C2

+ is at +5V, the

voltage potential across C

2 is l0V.

Phase 4

— V

DD transfer — The fourth phase of the clock

connects the negative terminal of C

2 to ground,

and transfers the generated l0V across C

2 to C4,

the V

DD storage capacitor. Again, simultaneously

with this, the positive side of capacitor C

1 is

switched to +5V and the negative side is con-

nected to ground, and the cycle begins again.

Since both V+ and V– are separately generated

from V

CC; in a no–load condition V

+ and V– will

be symmetrical. Older charge pump approaches

that generate V– from V+ will show a decrease in

the magnitude of V– compared to V+ due to the

inherent inefficiencies in the design.

The clock rate for the charge pump typically

operates at 15kHz. The external capacitors can

be as low as 0.1

µF with a 16V breakdown

voltage rating.

The SP200 Series devices are made up of three

basic circuit blocks — 1) transmitter/driver, 2)

receiver and 3) the Sipex proprietary charge

VCC = +5V

–5V

+5V

VSS Storage Capacitor

VDD Storage Capacitor

–

Figure 1. Charge Pump — Phase 1

Figure 2. Charge Pump — Phase 2

VCC = +5V

–10V

VSS Storage Capacitor

VDD Storage Capacitor

–

Número de Pieza	Descripción de Componentes	Html View	Fabricante
HIN200	+5V Powered RS-232 Transmitters/Receivers with 0.1Microfarad External Capacitors	1 2 3 4 5 More	Harris Corporation
HIN202_05	+5V Powered RS-232 Transmitters/Receivers with 0.1Microfarad External Capacitors	1 2 3 4 5 More	Intersil Corporation
MAX13050	Industry-Standard High-Speed CAN Transceivers with ±80V Fault Protection	1 2 3 4 5 More	Maxim Integrated Products
ICL3224_06	1 Microamp +3V to +5.5V 250kbps RS-232 Transceivers with Enhanced Automatic Powerdown	1 2 3 4 5 More	Intersil Corporation
ICL3225_06	1 Microamp +3V to +5.5V 1Mbps RS-232 Transceivers with Enhanced Automatic Powerdown	1 2 3 4 5 More	Intersil Corporation
ICL3224E_06	+/-15kV ESD Protected +3V to +5.5V 1Microamp 250kbps RS-232 Transceivers with Enhanced Automatic Powerdown	1 2 3 4 5 More	Intersil Corporation
ICL3225E_06	±15kV ESD Protected +3V to +5.5V 1Microamp 1Mbps RS-232 Transceivers with Enhanced Automatic Powerdown	1 2 3 4 5 More	Intersil Corporation
B43520A3687M000	Capacitors with 4 Snap-In Terminals and Solder Pins	1 2 3 4 5 More	EPCOS
MAX3221E_06	3-V TO 5.5-V SINGLE-CHANNEL RS-232 LINE DRIVER/RECEIVER WITH 15-kV IEC ESD PROTECTION	1 2 3 4 5 More	Texas Instruments
SN65C3232E	3-V TO 5.5-V TWO-CHANNEL RS-232 1-MBIT/S LINE DRIVERS/RECEIVERS WITH ±15-kV IEC ESD PROTECTION	1 2 3 4 5 More	Texas Instruments

Número de Pieza relacionado

Enlace URL

Patrocinador de Alldatasheet