ST95022M3TR datasheet(4/16 Pages) STMICROELECTRONICS

No. de pieza	ST95022M3TR

Descripción Electrónicos	2 Kbit Serial SPI EEPROM with High Speed Clock

Download	16 Pages

Scroll/Zoom	100%

Fabricante Electrónico	STMICROELECTRONICS [STMicroelectronics]

Página de inicio	http://www.st.com

Logo

4 / 16 page

OPERATIONS

All instructions, addresses and data are shifted in

and out of the chip MSB first. Data input (D) is

sampled on the first rising edge of clock (C) after

the chip select (S) goes low. Prior to any operation,

a one-byte instruction code must be entered in the

chip. This code is entered via the data input (D),

and latched on the rising edge of the clock input

(C). To enter an instruction code, the product must

have been previously selected (S = low). Table 3

shows the instruction set and format for device

operation. If an invalid instruction is sent (one not

contained in Table 3), the chip is automatically

deselected.

Write Enable (WREN) and Write Disable (WRDI)

The ST95022 contains a write enable latch. This

latch must be set prior to every WRITE or WRSR

operation. The WREN instruction will set the latch

and the WRDI instruction will reset the latch. The

latch is reset under the following conditions:

– W pin is low

– Power on

– WRDI instruction executed

– WRSR instruction executed

– WRITE instruction executed

As soon as the WREN or WRDI instruction is

received by the ST95022, the circuit executes the

instruction and enters a wait mode until it is dese-

lected.

Read Status Register (RDSR)

The RDSR instruction provides access to the status

register. The status register may be read at any

time, even during a write to the memory operation.

As soon as the 8th bit of the status register is read

out, the ST95022 enters a wait mode (data on D is

not decoded, Q is in Hi-Z) until it is deselected.

The status register format is as follows:

b7

b0

1

BP1

BP0

WEL

WIP

BP1, BP0: Read and write bits.

WEL, WIP: Read only bits.

b7 to b4: Read only bits.

During a write to the memory operation to the

memory array, all bits BP1, BP0, WEL, WIP are

valid and can be read. During a write to the status

register, only the bits WEL and WIP are valid and

can be read. The values of BP1 and BP0 read at

that time correspond to the previous contents of the

status register.

The Write-In-Process (WIP) read-only bit indicates

whether the ST95022 is busy with a write opera-

tion. When set to a ’1’ a write is in progress, when

set to a ’0’ no write is in progress.

The Write Enable Latch (WEL) read-only bit indi-

cates the status of the write enable latch. When set

to a ’1’ the latch is set, when set to a ’0’ the latch is

reset. The Block Protect (BP0 and BP1) bits indi-

cate the extent of the protection employed. These

bits are set by the user issuing the WRSR instruc-

tion. These bits are non-volatile.

Write Status Register (WRSR)

The WRSR instruction allows the user to select the

size of protected memory. The ST95022 is divided

into four 512 bit blocks. The user may read the

blocks but will be unable to write within the pro-

Instruction

Description

Instruction Format

WREN

Set Write Enable Latch

0000 0110

WRDI

Reset Write Enable Latch

0000 0100

RDSR

Read Status Register

0000 0101

WRSR

Write Status Register

0000 0001

READ

Read Data from Memory Array

0000 0011

WRITE

Write Data to Memory Array

0000 0010

Notes: A = 1, Upper page selected

A = 0, Lower page selected

Table 3. Instruction Set

4/16

ST95022

Número de pieza similar - ST95022M3TR

Fabricante Electrónico	No. de pieza	Datasheet	Descripción Electrónicos
STMicroelectronics	ST95020	110Kb / 18P	4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe
	ST95020B1TR	110Kb / 18P	4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe
	ST95020B3TR	110Kb / 18P	4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe
	ST95020B6TR	110Kb / 18P	4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe
	ST95020M1TR	110Kb / 18P	4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe

More results

Descripción similar - ST95022M3TR

Fabricante Electrónico	No. de pieza	Datasheet	Descripción Electrónicos
STMicroelectronics	M95040	373Kb / 42P	4 Kbit, 2 Kbit and 1 Kbit serial SPI bus EEPROM with high-speed clock
	M95040	335Kb / 42P	4 Kbit, 2 Kbit and 1 Kbit Serial SPI bus EEPROM with high speed Clock
	M95040	376Kb / 43P	4 Kbit, 2 Kbit and 1 Kbit serial SPI bus EEPROM with high-speed clock
	M95320-W	412Kb / 48P	32-Kbit serial SPI bus EEPROM with high-speed clock
	M95256	345Kb / 39P	256 Kbit Serial SPI bus EEPROM with high speed clock
	M95512-DR	483Kb / 48P	512 Kbit serial SPI bus EEPROM with high-speed clock
	M95160-WMN6TP	827Kb / 47P	16-Kbit serial SPI bus EEPROM with high-speed clock
	M95256-W	607Kb / 51P	256-Kbit serial SPI bus EEPROM with high-speed clock Rev 22 - September 2021
	M95640-W	905Kb / 53P	64-Kbit serial SPI bus EEPROM with high-speed clock Rev 19 February 2016
	M95256-DR	504Kb / 48P	256 Kbit serial SPI bus EEPROM with high-speed clock

More results

ST95022M3TR Datasheet(PDF) 4 Page - STMicroelectronics

ST95022M3TR Datasheet(HTML) 4 Page - STMicroelectronics

Número de pieza similar - ST95022M3TR

Descripción similar - ST95022M3TR

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Datasheet Descarga

Enlace URL