Motor de Búsqueda de Datasheet de Componentes Electrónicos
  Spanish  ▼
ALLDATASHEET.ES

X  

STA013B Datasheet(PDF) 9 Page - STMicroelectronics

No. de pieza STA013B
Descripción Electrónicos  MPEG 2.5 LAYER III AUDIO DECODER
Download  38 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrónico  STMICROELECTRONICS [STMicroelectronics]
Página de inicio  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

STA013B Datasheet(HTML) 9 Page - STMicroelectronics

Back Button STA013B Datasheet HTML 5Page - STMicroelectronics STA013B Datasheet HTML 6Page - STMicroelectronics STA013B Datasheet HTML 7Page - STMicroelectronics STA013B Datasheet HTML 8Page - STMicroelectronics STA013B Datasheet HTML 9Page - STMicroelectronics STA013B Datasheet HTML 10Page - STMicroelectronics STA013B Datasheet HTML 11Page - STMicroelectronics STA013B Datasheet HTML 12Page - STMicroelectronics STA013B Datasheet HTML 13Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 38 page
background image
2.5 - STA013 Operation Mode
The STA013 can work in two different modes,
called Multimedia Mode and Broadcast Mode.
In Multimedia Mode, STA013 decodes the in-
coming bitstream, acting as a master of the data
communication from the source to itself.
This control is done by a specific buffer manage-
ment, controlled by STA013 embedded software.
The data source, by monitoring the DATA_REQ
line, send to STA013 the input data, when the
signal is high (default configuration).
The
communication
is
stopped
when
the
DATA_REQ line is low.
In this mode the fractional part of the PLL is dis-
abled and the audio clocks are generated at
nominal rates. Fig. 9 describes the default
DATA_REQ signal behaviour.
Programming STA013 it is possible to invert the
polarity
of
the
DATA_REQ
line
(register
REQ_POL).
In Broadcast Mode, STA013 works receiving a
bitstream with the input speed regulated by the
source. In this configuration the source has to
guarantee that the bitrate is equivalent to the
nominal bitrate of the decoded stream.
To compensate the difference between the nomi-
nal and the real sampling rates, the STA013 em-
bedded software controls the fractional PLL op-
eration. Portable or Mobile applications need
normally to operate in Broadcast Mode. In both
modes the MPEG Synchronisation is automatic
and transparent to the user. To operate in Multi-
media mode, the STA013, pin nr. 8, SCR-INT
must be connected to VDD on the application
board.
2.6 - STA013 Decoding States
There are three different decoder states: Idle,
Init, and Decode. Commands to change the de-
coding states are described in the STA013 I
2C
registers description.
Idle Mode
In this mode the decoder is waiting for the RUN
command. This mode should be used to initialise
the configuration register of the device. The DAC
connected to STA013 can be initialised during
this mode (set MUTE to 1).
PLAY
MUTE
Clock State
PCM Output
X
0
Not Running
0
X
1
Running
0
Init Mode
"PLAY" and "MUTE" changes are ignored in this
mode. The internal state of the decoder will be
updated only when the decoder changes from the
state "init" to the state "decode". The "init" phase
ends when the first decoded samples are at the
output stage of the device.
Decode Mode
This mode is completely described by the follow-
ing table:
PLAY
MUTE
Clock State
PCM
Output
Decoding
0
0
Not Running
0
No
0
1
Running
0
No
1
0
Running
Decoded
Samples
Yes
1
1
Running
0
Yes
3 - I
2C BUS SPECIFICATION
The STA013 supports the I
2C protocol. This pro-
tocol defines any device that sends data on to the
bus as a transmitter and any device that reads
the data as a receiver. The device that controls
the data transfer is known as the master and the
others as the slave. The master always starts the
transfer and provides the serial clock for synchro-
nisation. The STA013 is always a slave device in
all its communications.
3. 1 - COMMUNICATION PROTOCOL
3.1.0 - Data transition or change
Data changes on the SDA line must only occur
when the SCL clock is low. SDA transition while
the clock is high are used to identify START or
STOP condition.
3.1.1 - Start condition
START is identified by a high to low transition of
the data bus SDA signal while the clock signal
SCL is stable in the high state.
A START condition must precede any command
for data transfer.
SOURCE SEND DATA TO STA013
DATA_REQ
SOURCE STOPS TRANSMITTING DATA
SOURCE STOPS TRANSMITTING DATA
D98AU913
Figure 9.
STA013 - STA013B - STA013T
9/38


Número de pieza similar - STA013B

Fabricante ElectrónicoNo. de piezaDatasheetDescripción Electrónicos
logo
STMicroelectronics
STA011 STMICROELECTRONICS-STA011 Datasheet
434Kb / 38P
   L-band RF front-end for digital radio
STA014 STMICROELECTRONICS-STA014 Datasheet
466Kb / 45P
   MPEG 2.5 LAYER III AUDIO DECODER WITH ADPCM AND SRS WOWO POSTPROCESSING CAPABILITY
STA014B STMICROELECTRONICS-STA014B Datasheet
466Kb / 45P
   MPEG 2.5 LAYER III AUDIO DECODER WITH ADPCM AND SRS WOWO POSTPROCESSING CAPABILITY
STA014T STMICROELECTRONICS-STA014T Datasheet
466Kb / 45P
   MPEG 2.5 LAYER III AUDIO DECODER WITH ADPCM AND SRS WOWO POSTPROCESSING CAPABILITY
STA015 STMICROELECTRONICS-STA015 Datasheet
277Kb / 44P
   MPEG 2.5 LAYER III AUDIO DECODER WITH ADPCM CAPABILITY
More results

Descripción similar - STA013B

Fabricante ElectrónicoNo. de piezaDatasheetDescripción Electrónicos
logo
STMicroelectronics
STA003T STMICROELECTRONICS-STA003T Datasheet
309Kb / 32P
   MPEG 2.5 LAYER III AUDIO DECODER
logo
Winbond
W9986D WINBOND-W9986D Datasheet
128Kb / 1P
   MPEG Audio Layer III Decoder
logo
STMicroelectronics
STA015 STMICROELECTRONICS-STA015 Datasheet
277Kb / 44P
   MPEG 2.5 LAYER III AUDIO DECODER WITH ADPCM CAPABILITY
STA015 STMICROELECTRONICS-STA015_04 Datasheet
720Kb / 55P
   MPEG 2.5 LAYER III AUDIO DECODER WITH ADPCM CAPABILITY
STA015 STMICROELECTRONICS-STA015_10 Datasheet
1Mb / 56P
   MPEG 2.5 LAYER III AUDIO DECODER WITH ADPCM CAPABILITY
STA016A STMICROELECTRONICS-STA016A Datasheet
268Kb / 43P
   MPEG 2.5 LAYER III AUDIO DECODER SUPPORTING CD-ROM CAPABILITY
STA016T STMICROELECTRONICS-STA016T Datasheet
249Kb / 45P
   MPEG 2.5 LAYER III AUDIO DECODER SUPPORTING CD-ROM CAPABILITY & ADPCM
STA014 STMICROELECTRONICS-STA014 Datasheet
466Kb / 45P
   MPEG 2.5 LAYER III AUDIO DECODER WITH ADPCM AND SRS WOWO POSTPROCESSING CAPABILITY
logo
Micronas
MAS3507D MICRONAS-MAS3507D Datasheet
867Kb / 60P
   MPEG 1/2 Layer 2/3 Audio Decoder
logo
Sanyo Semicon Device
LC8230 SANYO-LC8230 Datasheet
138Kb / 7P
   MPEG Audio Decoder LSI
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38


Datasheet Descarga

Go To PDF Page


Enlace URL




Política de Privacidad
ALLDATASHEET.ES
¿ALLDATASHEET es útil para Ud.?  [ DONATE ] 

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com