TLC1542EP, TLC1543EP

10BIT ANALOGTODIGITAL CONVERTERS WITH

SERIAL CONTROL AND 11 ANALOG INPUTS

SGLS152A − JANUARY 2004 − REVISED FEBRUARY 2006

5

POST OFFICE BOX 655303

mode 2: fast mode, CS active (low) continuously, 10-clock transfer

In this mode, CS is active (low) between serial I/O CLOCK transfers and each transfer is 10 clocks long. After

the initial conversion cycle, CS is held active (low) for subsequent conversions; the rising edge of EOC then

begins each sequence by removing DATA OUT from the low logic level, allowing the MSB of the previous

conversion to appear immediately on this output.

mode 3: fast mode, CS inactive (high) between conversion cycles, 11- to 16-clock transfer

In this mode, CS is inactive (high) between serial I/O CLOCK transfers, and each transfer can be 11 to 16 clocks

long. The falling edge of CS begins the sequence by removing DATA OUT from the high-impedance state. The

rising edge of CS ends the sequence by returning DATA OUT to the high-impedance state within the specified

delay time. Also, the rising edge of CS disables the I/O CLOCK and ADDRESS terminals within a setup time

plus two falling edges of the internal system clock.

mode 4: fast mode, CS active (low) continuously, 16-clock transfer

In this mode, CS is active (low) between serial I/O CLOCK transfers and each transfer must be exactly 16 clocks

long. After the initial conversion cycle, CS is held active (low) for subsequent conversions; the rising edge of

EOC then begins each sequence by removing DATA OUT from the low logic level, allowing the MSB of the

previous conversion to appear immediately on this output.

slow modes

In a slow mode, the conversion is completed before the serial I/O CLOCK data transfer is completed. A slow

mode requires a minimum 11-clock transfer into I/O CLOCK and the rising edge of the eleventh clock must occur

before the conversion period is complete; otherwise, the device loses synchronization with the host-serial

interface and CS has to be toggled to initialize the system. The eleventh rising edge of the I/O CLOCK must

occur within 9.5

µs after the tenth I/O clock falling edge.

mode 5: slow mode, CS inactive (high) between conversion cycles, 11- to 16-clock transfer

In this mode, CS is inactive (high) between serial I/O CLOCK transfers and each transfer can be 11 to 16 clocks

long. The falling edge of CS begins the sequence by removing DATA OUT from the high-impedance state. The

rising edge of CS ends the sequence by returning DATA OUT to the high-impedance state within the specified

delay time. Also, the rising edge of CS disables the I/O CLOCK and ADDRESS terminals within a setup time

plus two falling edges of the internal system clock.

mode 6: slow mode, CS active (low) continuously, 16-clock transfer

In this mode, CS is active (low) between serial I/O CLOCK transfers and each transfer must be exactly 16 clocks

long. After the initial conversion cycle, CS is held active (low) for subsequent conversions. The falling edge of

the sixteenth I/O CLOCK then begins each sequence by removing DATA OUT from the low state, allowing the

MSB of the previous conversion to appear immediately at DATA OUT. The device is then ready for the next

16-clock transfer initiated by the serial interface.

address bits

The 4-bit analog channel-select address for the next conversion cycle is presented to the ADDRESS terminal

(MSB first) and is clocked into the address register on the first four leading edges of I/O CLOCK. This address

selects one of 14 inputs (11 analog inputs or three internal test inputs).

analog inputs and test modes

The 11 analog inputs and the three internal test inputs are selected by the 14-channel multiplexer according

to the input address as shown in Tables 2 and 3. The input multiplexer is a break-before-make type to reduce

input-to-input noise injection resulting from channel switching.

Sampling of the analog input starts on the falling edge of the fourth I/O CLOCK, and sampling continues for six

I/O CLOCK periods. The sample is held on the falling edge of the tenth I/O CLOCK. The three test inputs are

applied to the multiplexer, sampled, and converted in the same manner as the external analog inputs.