Motor de Búsqueda de Datasheet de Componentes Electrónicos
  Spanish  ▼
ALLDATASHEET.ES

X  

LM1894N Datasheet(PDF) 5 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
No. de pieza LM1894N
Descripción Electrónicos  Dynamic Noise Reduction System DNR
Download  10 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrónico  NSC [National Semiconductor (TI)]
Página de inicio  http://www.national.com
Logo NSC - National Semiconductor (TI)

LM1894N Datasheet(HTML) 5 Page - National Semiconductor (TI)

  LM1894N Datasheet HTML 1Page - National Semiconductor (TI) LM1894N Datasheet HTML 2Page - National Semiconductor (TI) LM1894N Datasheet HTML 3Page - National Semiconductor (TI) LM1894N Datasheet HTML 4Page - National Semiconductor (TI) LM1894N Datasheet HTML 5Page - National Semiconductor (TI) LM1894N Datasheet HTML 6Page - National Semiconductor (TI) LM1894N Datasheet HTML 7Page - National Semiconductor (TI) LM1894N Datasheet HTML 8Page - National Semiconductor (TI) LM1894N Datasheet HTML 9Page - National Semiconductor (TI) Next Button
Zoom Inzoom in Zoom Outzoom out
 5 / 10 page
background image
External Component Guide
(
Figure 1)
Component
Value
Purpose
C1
0.1 µF–
100 µF
May be part of power supply,
or may be added to suppress
power supply oscillation.
C2, C13
1 µF
Blocks DC, pin 2 and pin 13
are at DC potential of V
S/2.
C2, C13 form a low frequency
pole with 20k R
IN.
C14
25 µF–
100 µF
Improves power supply
rejection.
C3, C12
0.0033 µF
Forms integrator with internal
gm block and op amp. Sets
bandwidth conversion gain of
33 Hz/µA of gm current.
C4, C11
1 µF
Output coupling capacitor.
Output is at DC potential of
V
S/2.
C5
0.1 µF
Works with R1 and R2 to
attenuate low frequency
transients which could disturb
control path operation.
C6
0.001 µF
Works with input resistance of
pin 6 to form part of control
path frequency weighting.
C8
0.1 µF
Combined with L8 and C
L
forms 19 kHz filter for FM
pilot. This is only required in
FM applications (Note 9).
L8, C
L
4.7 mH,
0.015 µF
Forms 19 kHz filter for FM
pilot. L8 is Toko coil
CAN-1A185HM (Notes 8, 9).
C9
0.047 µF
Works with input resistance of
pin 9 to form part of control
path frequency weighting.
C10
1 µF
Set attack and decay time of
peak detector.
R1, R2
1 k
Sensitivity resistors set the
noise threshold. Reducing
attentuation causes larger
signals to be peak detected
and larger bandwidth in main
signal path. Total value of R1
+ R2 should equal 1 k
Ω.
R8
100
Forms RC roll-off with C8.
This is only required in FM
applications.
Note 8: Toko America Inc., 1250 Feehanville Drive, Mt. Prospect IL 60056
Note 9: When FM applications are not required, pin 8 and pin 9 hook-up as
follows:
Circuit Operation
The LM1894 has two signal paths, a main signal path and a
bandwidth control path. The main path is an audio low pass
filter comprised of a gm block with a variable current, and an
op amp configured as an integrator. As seen in
Figure 2,DC
feedback constrains the low frequency gain to A
V = −1.
Above the cutoff frequency of the filter, the output decreases
at −6 dB/oct due to the action of the 0.0033 µF capacitor.
The purpose of the control paths is to generate a bandwidth
control signal which replicates the ear’s sensitivity to noise in
the presence of a tone. A single control path is used for both
channels to keep the stereo image from wandering. This is
done by adding the right and left channels together in the
summing amplifier of
Figure 2. The R1, R2 resistor divider
adjusts the incoming noise level to open slightly the band-
width of the low pass filter. Control path gain is about 60 dB
and is set by the gain amplifier and peak detector gain. This
large gain is needed to ensure the low pass filter bandwidth
can be opened by very low noise floors. The capacitors be-
tween the summing amplifier output and the peak detector
input determine the frequency weighting as shown in the
typical performance curves. The 1 µF capacitor at pin 10, in
conjunction with internal resistors, sets the attack and decay
times. The voltage is converted into a proportional current
which is fed into the gm blocks. The bandwidth sensitivity to
gm current is 33 Hz/µA. In FM stereo applications at 19 kHz
pilot filter is inserted between pin 8 and pin 9 as shown in
Figure 1.
Figure 3 is an interesting curve and deserves some discus-
sion. Although the output of the DNR system is a linear func-
tion of input signal, the −3 dB bandwidth is not. This is due to
the non-linear nature of the control path. The DNR system
has a uniform frequency response, but looking at the −3 dB
bandwidth on a steady state basis with a single frequency in-
put can be misleading. It must be remembered that a single
input frequency can only give a single −3 dB bandwidth and
the roll-off from this point must be a smooth −6 dB/oct.
A more accurate evaluation of the frequency response can
be seen in
Figure 4. In this case the main signal path is fre-
quency swept, while the control path has a constant fre-
quency applied. It can be seen that different control path fre-
quencies each give a distinctive gain roll-off.
Psychoacoustic Basics
The dynamic noise reduction system is a low pass filter that
has a variable bandwidth of 1 kHz to 30 kHz, dependent on
music spectrum. The DNR system operates on three prin-
ciples of psychoacoustics.
1. White noise can mask pure tones. The total noise energy
required to mask a pure tone must equal the energy of the
tone itself. Within certain limits, the wider the band of mask-
ing noise about the tone, the lower the noise amplitude need
DS007918-6
www.national.com
5


Número de pieza similar - LM1894N

Fabricante ElectrónicoNo. de piezaDatasheetDescripción Electrónicos
logo
Texas Instruments
LM1894 TI1-LM1894 Datasheet
988Kb / 19P
[Old version datasheet]   Dynamic Noise Reduction System DNR
LM1894MX/NOPB TI1-LM1894MX/NOPB Datasheet
988Kb / 19P
[Old version datasheet]   Dynamic Noise Reduction System DNR
More results

Descripción similar - LM1894N

Fabricante ElectrónicoNo. de piezaDatasheetDescripción Electrónicos
logo
Texas Instruments
LM1894 TI1-LM1894 Datasheet
988Kb / 19P
[Old version datasheet]   Dynamic Noise Reduction System DNR
logo
National Semiconductor ...
LM832 NSC-LM832 Datasheet
197Kb / 10P
   Dynamic Noise Reduction System DNR
August 1989
logo
Renesas Technology Corp
HA12181FP RENESAS-HA12181FP Datasheet
302Kb / 20P
   AM Radio Noise Reduction System
logo
Hitachi Semiconductor
HA12181FP HITACHI-HA12181FP Datasheet
147Kb / 21P
   AM Radio Noise Reduction System
logo
Sony Corporation
CXA1100P SONY-CXA1100P Datasheet
473Kb / 15P
   DOLBY B TYPE NOISE REDUCTION SYSTEM
CXA1550P SONY-CXA1550P Datasheet
232Kb / 16P
   Dolby B type Noise Reduction System
logo
Hitachi Semiconductor
HA12134A HITACHI-HA12134A Datasheet
130Kb / 27P
   Dolby B-Type Noise Reduction System
12136AF HITACHI-12136AF Datasheet
101Kb / 27P
   Dolby B-Type Noise Reduction System
logo
NTE Electronics
NTE1801 NTE-NTE1801 Datasheet
22Kb / 3P
   Integrated Circuit TV dbx Noise Reduction System
logo
Sony Corporation
CX20188 SONY-CX20188 Datasheet
1Mb / 22P
   DOLBY B-C TYPE NOISE REDUCTION SYSTEM
More results


Html Pages

1 2 3 4 5 6 7 8 9 10


Datasheet Descarga

Go To PDF Page


Enlace URL




Política de Privacidad
ALLDATASHEET.ES
¿ALLDATASHEET es útil para Ud.?  [ DONATE ] 

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com