Motor de Búsqueda de Datasheet de Componentes Electrónicos
  Spanish  ▼
ALLDATASHEET.ES

X  

543415-1 Datasheet(PDF) 1 Page - TE Connectivity Ltd

No. de pieza 543415-1
Descripción Electrónicos  This instruction sheet covers the use and maintenance of Crimping Die Assemblies
Download  4 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrónico  TEC [TE Connectivity Ltd]
Página de inicio  http://www.te.com/usa-en/home.html
Logo TEC - TE Connectivity Ltd

543415-1 Datasheet(HTML) 1 Page - TE Connectivity Ltd

  543415-1 Datasheet HTML 1Page - TE Connectivity Ltd 543415-1 Datasheet HTML 2Page - TE Connectivity Ltd 543415-1 Datasheet HTML 3Page - TE Connectivity Ltd 543415-1 Datasheet HTML 4Page - TE Connectivity Ltd  
Zoom Inzoom in Zoom Outzoom out
 1 / 4 page
background image
©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
1 of 4
Instruction Sheet
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
LOC B
408-8609
Crimping Die Assemblies 1583015-1,
-2, -3, and 1583016-1 for High Speed
Serial Data Connector 2 (HSSDC2)
19 DEC 11 Rev A
Figure 1
1. INTRODUCTION
This instruction sheet covers the use and maintenance
of Crimping Die Assemblies 1583015-1, -2, -3, and
1583016-1, which are designed to be used in Hand
Crimping Tool Frame Assembly 543344-1 or 58235-1,
or in Pneumatic Power Unit 312522-3 equipped with
Die Holder Assembly 58449-1. Each die assembly
crimps a ferrule onto round shielded cable used with
HSSDC2 Connectors.
Reason for revision is given in Section 7, REVISON
SUMMARY.
Dimensions are in millimeters [with inches in
brackets]. Figures and illustrations are for
reference only and are not drawn to scale.
2. DESCRIPTION
Each die assembly consists of an indenter (stationary
die) and an anvil (moving die). When mated, the dies
form two crimping sections: the braid and the
insulation. The braid section crimps the front part of
the ferrule onto the cable shield and the cable outlet of
the connector shield assembly, and simultaneously,
the insulation section crimps the back part of the
ferrule onto the cable insulation. The anvil die is
designed with a stop to ensure proper positioning of
the ferrule for crimping. See Figure 1.
The ferrule, which is ordered separately from the
AMPLIMITE* connector, is sized according to the
insulation diameter of the cable. Each die assembly is
marked with the cable insulation diameter range.
3. DIE ASSEMBLY INSTALLATION
The die assembly is designed to fit securely into the
tool by upper and lower die holder plates; each die is
held in by a single screw. To install the die assembly,
refer to the instructions packaged with the tool:
408-9315
Hand Crimping Tool Frame Assembly
543344-1
408-9245
Hand Crimping Tool Frame Assembly
58235-1
408-9721
Die Holder Assembly 58449-1
409-5822
Pneumatic Power Unit 312522-3
4. CRIMPING PROCEDURE
Assemble the connector. Make sure the ferrule is over
the connector shield cable outlet and butted against
the shield body. Then, proceed as follows:
1. Place the ferrule on the moving die, with the
cable extending out the back side of the die. Make
sure that the front part of the ferrule is positioned in
the braid section and the back part of the ferrule is
positioned in the insulation section. See Figure 2.
The front edge of the ferrule must be against the
stop and the connector body must be clear of the
dies.
2. Actuate tool for crimping according to the
instructions packaged with the tool.
3. Remove connector from die assembly and
inspect the crimped ferrule to the requirements
outlined in the applicable application specification:
114-13028
High Speed Serial Data
Connector 2 (HSSDC2)
See Figure 3 for a properly crimped ferrule.
5. MAINTENANCE AND INSPECTION PROCEDURE
The die assembly is inspected prior to shipment,
however, it is recommended that the die assembly be
inspected immediately upon arrival. TE Connectivity
recommends that a maintenance and inspection
program be performed periodically to ensure
continued reliability of the die assembly. The
inspection frequency should be based on the amount
of use, working conditions, operator training and skill,
and established company standards.
NOTE
i
CAUTION
!


Número de pieza similar - 543415-1

Fabricante ElectrónicoNo. de piezaDatasheetDescripción Electrónicos
logo
PHOENIX CONTACT
5434159 PHOENIX-5434159 Datasheet
59Kb / 3P
   Printed-circuit board connector - BCH-508VF- 5 GY
More results

Descripción similar - 543415-1

Fabricante ElectrónicoNo. de piezaDatasheetDescripción Electrónicos
logo
Tyco Electronics
408-4199 MACOM-408-4199 Datasheet
346Kb / 7P
   This instruction sheet covers the application and maintenance procedures for Crimping Die Assembly
408-9451 MACOM-408-9451 Datasheet
86Kb / 2P
   This instruction sheet covers the use of Extraction
408-4198 MACOM-408-4198 Datasheet
378Kb / 6P
   This instruction sheet covers the application and maintenance procedures for Pneumatic Crimping Head Assembly
logo
TE Connectivity Ltd
408-7347 TEC-408-7347 Datasheet
137Kb / 2P
   This instruction sheet covers the use of insertion tools
408-9598 TEC-408-9598 Datasheet
398Kb / 5P
   This instruction sheet covers application and maintenance procedures for Hydraulic Crimping Head
408-8959 TEC-408-8959 Datasheet
291Kb / 6P
   This instruction sheet covers application, inspection and maintenance procedures for Hydraulic Crimping Head
408-9227 TEC-408-9227 Datasheet
134Kb / 4P
   Application and Maintenance for Crimping Die Assemblies
408-10243 TEC-408-10243 Datasheet
723Kb / 5P
   This instruction sheet provides information on the application and maintenance procedures for the SDE PEW-12 Hand Crimping
logo
Tyco Electronics
408-9785 MACOM-408-9785 Datasheet
260Kb / 6P
   This instruction sheet provides instruction on product application and maintenance and inspection
408-9452 MACOM-408-9452 Datasheet
90Kb / 2P
   This instruction sheet covers Extraction Tools
More results


Html Pages

1 2 3 4


Datasheet Descarga

Go To PDF Page


Enlace URL




Política de Privacidad
ALLDATASHEET.ES
¿ALLDATASHEET es útil para Ud.?  [ DONATE ] 

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com