Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
Si8285CD-IS Datasheet(PDF) 6 Page - Silicon Laboratories |
|
Si8285CD-IS Datasheet(HTML) 6 Page - Silicon Laboratories |
6 / 32 page 2.5 Desaturation Detection The Si828x provides sufficient voltage and current to drive and keep the IGBT in saturation during on time to minimize power dissipa- tion and maintain high efficiency operation. However, abnormal load conditions can force the IGBT out of saturation and cause perma- nent damage to the IGBT. To protect the IGBT during abnormal load conditions, the Si828x detects an IGBT desaturation condition, shuts down the driver upon detecting a fault, and provides a fault indication to the controller. These integrated features provide desaturation protection with mini- mum external BOM cost. The figure below illustrates the Si828x desaturation circuit. When the Si828x driver output is high, the internal current source is on, and this current flows from the DSAT pin to charge the CBL capacitor. The voltage on the DSAT pin is monitored by an internal comparator. Since the DSAT pin is connected to the IGBT collector through the DDSAT and a small RDSAT, its voltage is almost the same as the VCE of the IGBT. If the VCE of the IGBT does not drop below the Si828x desaturation threshold voltage within a certain time after turning on the IGBT (blanking period) the block will generate a fault signal. The Si828x desaturation hysteresis is fixed at 220 mV and threshold is nominally 7 V. VMID DSAT DESAT Sense Driver ControlSignal Fault Signal Driver Disable CBL RDSAT DDSAT 7 V Ichg Figure 2.3. Desaturation Circuit As an additional feature, the block supports a blanking timer function to mask the turn-on transient of the external switching device and avoid unexpected fault signal generation. This function requires an external blanking capacitor, CBL, of typically 100 pF between DSAT and VMID pins. The block includes a 1 mA current source (IChg) to charge the CBL. This current source, the value of the external CBL, and the programmed fault threshold, determine the blanking time (tBlanking). tBlanking = CBI × V DESAT Ichg An internal nmos switch is implemented between DSAT and VMID to discharge the external blanking capacitor, CBL, and reset the blanking timer. The current limiting RDSAT resistor protects the DSAT pin from large current flow toward the IGBT collector during the IGBT’s body diode freewheeling period (with possible large collector’s negative voltage, relative to IGBT’s emitter). 2.6 Soft Shutdown To avoid excessive dV/dt on the IGBT’s collector during fault shut down, the Si828x implements a soft shut down feature to discharge the IGBT’s gate slowly. When soft shut down is activated, the high power driver goes inactive, and a weak pull down via VH and exter- nal RH discharges the gate until the gate voltage level is reduced to the VSSB + 2 V level. The high power driver is then turned on to clamp the IGBT gate voltage to VMID. After the soft shut down, the Si828x driver output voltage is clamped low to keep the IGBT in the off state. Si8285/86 Data Sheet System Overview silabs.com | Smart. Connected. Energy-friendly. Preliminary Rev. 0.6 | 5 |
Número de pieza similar - Si8285CD-IS |
|
Descripción similar - Si8285CD-IS |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |