Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
LM2422 Datasheet(PDF) 7 Page - National Semiconductor (TI) |
|
|
LM2422 Datasheet(HTML) 7 Page - National Semiconductor (TI) |
7 / 8 page Application Hints (Continued) Figure 10 shows the maximum power dissipation of the LM2422 vs. Frequency when all three channels of the device are driving into a 10 pF load with a 110V P-P alternating one pixel on, one pixel off. Note that the frequency given in Figure 10 is half of the pixel frequency. The graph assumes a 72% active time (device operating at the specified fre- quency), which is typical in a TV application. The other 28% of the time the device is assumed to be sitting at the black level (190V in this case). A TV picture will not have frequency content over the whole picture exceeding 20 MHz. It is important to establish the worst case condition under normal viewing to give a realistic worst-case power dissipation for the LM2422. One test isa1to30MHz sine wave sweep over the active line. This would give a slightly lower power than taking the average of the power between 1 and 30 MHz. This average is 23.5 W. A sine wave will dissipate slightly less power, probably about 21 W or 22 W of power dissipa- tion. All of this information is critical for the designer to establish the heat sink requirement for his application. The designer should note that if the load capacitance is in- creased the AC component of the total power dissipation will also increase. The LM2422 case temperature must be maintained below 110˚C given the maximum power dissipation estimate of 22W. If the maximum expected ambient temperature is 60˚C and the maximum power dissipation is 22W then a maximum heat sink thermal resistance can be calculated: This example assumes a capacitive load of 10 pF and no resistive load. The designer should note that if the load capacitance is increased the AC component of the total power dissipation will also increase. OPTIMIZING TRANSIENT RESPONSE Referring to Figure 13, there are three components (R1, R2 and L1) that can be adjusted to optimize the transient re- sponse of the application circuit. Increasing the values of R1 and R2 will slow the circuit down while decreasing over- shoot. Increasing the value of L1 will speed up the circuit as well as increase overshoot. It is very important to use induc- tors with very high self-resonant frequencies, preferably above 300 MHz. Ferrite core inductors from J.W. Miller Magnetics (part # 78FR--K) were used for optimizing the performance of the device in the NSC application board. The values shown in Figure 13 can be used as a good starting point for the evaluation of the LM2422. Using a variable resistor for R1 will simplify finding the value needed for optimum performance in a given application. Once the opti- mum value is determined the variable resistor can be re- placed with a fixed value. Due to arc over considerations it is recommended that the values shown in Figure 13 not be changed by a large amount. Figure 12 shows the typical cathode pulse response with an output swing of 110V PP inside a modified production TV set using the LM1237 pre-amp. PC BOARD LAYOUT CONSIDERATIONS For optimum performance, an adequate ground plane, iso- lation between channels, good supply bypassing and mini- mizing unwanted feedback are necessary. Also, the length of the signal traces from the signal inputs to the LM2422 and from the LM2422 to the CRT cathode should be as short as possible. The following references are recommended: Ott, Henry W., “Noise Reduction Techniques in Electronic Systems”, John Wiley & Sons, New York, 1976. “Video Amplifier Design for Computer Monitors”, National Semiconductor Application Note 1013. Pease, Robert A., “Troubleshooting Analog Circuits”, Butterworth-Heinemann, 1991. Because of its high small signal bandwidth, the part may oscillate in a TV if feedback occurs around the video channel through the chassis wiring. To prevent this, leads to the video amplifier input circuit should be shielded, and input circuit wiring should be spaced as far as possible from output circuit wiring. TYPICAL APPLICATION The typical application for the LM2422 is in HDTV systems with scan rates as high as 1080i. Full resolution of a 1080i system requires 30 MHz of bandwidth matching the capabil- ity of the LM2422. Used in conjunction with an AVP with a 1.2V black level output no buffer transistors are required to obtain the correct black level at the cathodes. If the AVP has a black level closer to 2V, then an NPN transistor should be used to drop the video black level voltage closer to 1.2V. Some AVPs have black levels at about 2.5V. This level would require two buffer transistors to drop the black level to the desired 1.2V. For more information on typical applications or for demonstration boards please contact your local National Semiconductor representative. www.national.com 7 |
Número de pieza similar - LM2422 |
|
Descripción similar - LM2422 |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |