Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
74LVT125D Datasheet(PDF) 6 Page - NXP Semiconductors |
|
74LVT125D Datasheet(HTML) 6 Page - NXP Semiconductors |
6 / 10 page 9397 750 14703 © Koninklijke Philips Electronics N.V. 2005. All rights reserved. Product data sheet Rev. 05 — 10 February 2005 6 of 15 Philips Semiconductors 74LVT125 3.3 V quad buffer; 3-state [1] Typical values are measured at VCC = 3.3 V and Tamb =25 °C. [2] Unused pins at VCC or GND. [3] This is the bus hold overdrive current required to force the input to the opposite logic state. [4] This parameter is valid for any VCC between 0 V and 1.2 V with a transition time of up to 10 ms. From VCC = 1.2 VtoVCC = 3.3 V ± 0.3 V a transition time of 100 µs is permitted. This parameter is valid for T amb =25 °C only. [5] ICC is measured with outputs pulled to VCC or GND. [6] This is the increase in supply current for each input at the specified voltage level other than VCC or GND. 11. Dynamic characteristics IEX external current into output output in HIGH-state when VO >VCC; VO = 5.5 V and VCC = 3.0 V - 60 125 µA IPU, IPD power-up or power-down 3-state output current VCC ≤ 1.2 V; VO = 0.5 V to VCC; VI = GND or VCC; nOE = don’t care [4] - ±1 ±100 µA IOZ 3-state output current VCC = 3.6 V; VI =VIH or VIL output HIGH: VO = 3.0 V - 1 5 µA output LOW: VO = 0.5 V - −1 −5 µA ICC quiescent supply current VCC = 3.6 V; VI = GND or VCC; IO =0A outputs HIGH - 0.13 0.19 mA outputs LOW - 2 7 mA outputs disabled [5] - 0.13 0.19 mA ∆ICC additional supply current per input pin VCC = 3 V to 3.6 V; one input at VCC − 0.6 V and other inputs at VCC or GND; [6] - 0.1 0.2 mA CI input capacitance VI = 0 V or 3.0 V - 4 - pF CO output capacitance outputs disabled; VO = 0 V or 3.0 V -8 -pF Table 7: Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V). Symbol Parameter Conditions Min Typ Max Unit Table 8: Dynamic characteristics GND = 0 V; tr =tf = 2.5 ns; CL = 50 pF; RL = 500 Ω; for test circuit see Figure 8. Symbol Parameter Conditions Min Typ Max Unit Tamb = −40 °C to +85 °C [1] tPLH propagation delay nA to nY VCC = 2.7 V - - 4.5 ns VCC = 3.3 V ± 0.3 V 1.0 2.7 4.0 ns tPHL propagation delay nA to nY VCC = 2.7 V - - 4.9 ns VCC = 3.3 V ± 0.3 V 1.0 2.9 3.9 ns tPZH output enable time nOE to nY VCC = 2.7 V - - 6.0 ns VCC = 3.3 V ± 0.3 V 1.0 3.4 4.7 ns tPZL output enable time nOE to nY VCC = 2.7 V - - 6.5 ns VCC = 3.3 V ± 0.3 V 1.1 3.4 4.7 ns |
Número de pieza similar - 74LVT125D |
|
Descripción similar - 74LVT125D |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |