LM2575_05 datasheet(11/28 Pages) ONSEMI

No. de pieza	LM2575

Descripción Electrónicos	1.0 A, Adjustable Output Voltage, Step?묭own Switching Regulator

Download	28 Pages

Scroll/Zoom	100%

Fabricante Electrónico	ONSEMI [ON Semiconductor]

Página de inicio	http://www.onsemi.com

Logo

11 / 28 page

LM2575

http://onsemi.com

11

Procedure (Adjustable Output Version: LM2575−Adj) (continued)

Procedure

Example

4. Inductor Selection (L1)

A. Use the following formula to calculate the inductor Volt x

microsecond [V x

ms] constant:

B. Match the calculated E x T value with the corresponding

number on the vertical axis of the Inductor Value Selection

Guide shown in Figure 21. This E x T constant is a measure

of the energy handling capability of an inductor and is

dependent upon the type of core, the core area, the number

of turns, and the duty cycle.

C. Next step is to identify the inductance region intersected by

the E x T value and the maximum load current value on the

horizontal axis shown in Figure 21.

D. From the inductor code, identify the inductor value. Then

select an appropriate inductor from the Table 1 or Table 2.

The inductor chosen must be rated for a switching

frequency of 52 kHz and for a current rating of 1.15 x IIoad.

The inductor current rating can also be determined by

calculating the inductor peak current:

where ton is the “on” time of the power switch and

For additional information about the inductor, see the

inductor section in the “External Components” section of

this data sheet.

ExT

+ V

in

–Vout

Vout

Von

x

106

F[Hz]

[V x

ms]

I

p(max)

+ I

Load(max) )

V

in

–Vout ton

2L

ton +

Vout

V

in

x

1

fosc

4. Inductor Selection (L1)

A. Calculate E x T [V x

ms] constant:

B. E x T = 51 [V x

ms]

C. ILoad(max) = 1.0 A

Inductance Region = L220

D. Proper inductor value = 220

mH

Choose the inductor from the Table 1 or Table 2.

ExT

+ (12–8.0) x 8.0

12

x

1000

52

+ 51 [V x ms]

5. Output Capacitor Selection (Cout)

A. Since the LM2575 is a forward−mode switching regulator

with voltage mode control, its open loop 2−pole−2−zero

frequency characteristic has the dominant pole−pair

determined by the output capacitor and inductor values.

For stable operation, the capacitor must satisfy the

following requirement:

B. Capacitor values between 10

mF and 2000 mF will satisfy

the loop requirements for stable operation. To achieve an

acceptable output ripple voltage and transient response, the

output capacitor may need to be several times larger than

the above formula yields.

C. Due to the fact that the higher voltage electrolytic capacitors

generally have lower ESR (Equivalent Series Resistance)

numbers, the output capacitor’s voltage rating should be at

least 1.5 times greater than the output voltage. For a 5.0 V

regulator, a rating of at least 8V is appropriate, and a 10 V

or 16 V rating is recommended.

C

out w

7.785

V

in(max)

Vout xL[μH]

[

μF]

5. Output Capacitor Selection (Cout)

A.

To achieve an acceptable ripple voltage, select

Cout = 100 mF electrolytic capacitor.

C

out w

7.785

12

8.220

+ 53 μF

Número de pieza similar - LM2575_05

Fabricante Electrónico	No. de pieza	Datasheet	Descripción Electrónicos
Texas Instruments	LM2575-05IKC	195Kb / 12P	[Old version datasheet] 1-A SIMPLE STEP DOWN SWITCHING VOLTAGE REGULATOR
	LM2575-05IKTGR	195Kb / 12P	[Old version datasheet] 1-A SIMPLE STEP DOWN SWITCHING VOLTAGE REGULATOR
	LM2575-05IKTT	195Kb / 12P	[Old version datasheet] 1-A SIMPLE STEP DOWN SWITCHING VOLTAGE REGULATOR
	LM2575-05IKTTR	195Kb / 12P	[Old version datasheet] 1-A SIMPLE STEP DOWN SWITCHING VOLTAGE REGULATOR
	LM2575-05IN	195Kb / 12P	[Old version datasheet] 1-A SIMPLE STEP DOWN SWITCHING VOLTAGE REGULATOR

More results

Descripción similar - LM2575_05

Fabricante Electrónico	No. de pieza	Datasheet	Descripción Electrónicos
ON Semiconductor	LM2574	296Kb / 26P	0.5 A, Adjustable Output Voltage, Step?묭own Switching Regulator August, 2006 ??Rev. 8
	LM2575T-15G	497Kb / 28P	1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator June, 2009 ??Rev. 11
	LM2575T-005G	461Kb / 28P	1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator June, 2009 ??Rev. 11
	LM2575	382Kb / 26P	1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator May, 2004 ??Rev. 6
	LM2575	497Kb / 28P	1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator June, 2009 ??Rev. 11
	LM2575T-ADJ	497Kb / 28P	1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator June, 2009 ??Rev. 11
	LM2575D2T-005	461Kb / 28P	1.0 A, Adjustable Output Voltage, Step-Down June, 2009 ??Rev. 11
	LM2574	279Kb / 28P	0.5 A, Adjustable Output Voltage, Step-Down Switching Regulator February, 2002 ??Rev. 5
	LM2574	234Kb / 26P	0.5 A, Adjustable Output Voltage, Step-Down Switching Regulator January, 2015 ??Rev. 9
	LM2576	276Kb / 28P	3.0 A, 15 V, Step?묭own Switching Regulator January, 2006 ??Rev. 8

More results

LM2575 Datasheet(PDF) 11 Page - ON Semiconductor

LM2575 Datasheet(HTML) 11 Page - ON Semiconductor

Número de pieza similar - LM2575_05

Descripción similar - LM2575_05

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Datasheet Descarga

Enlace URL