Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
74LVTH162373ZQLR Datasheet(PDF) 2 Page - Texas Instruments |
|
74LVTH162373ZQLR Datasheet(HTML) 2 Page - Texas Instruments |
2 / 14 page www.ti.com DESCRIPTION/ORDERING INFORMATION (CONTINUED) TERMINAL ASSIGNMENTS (1) GQL ORZQL PACKAGE (TOP VIEW) J H G F E D C B A 2 1 3 4 6 5 K SN54LVTH162373 ,, SN74LVTH162373 3.3-V ABT 16-BIT TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS SCBS261M – JULY 1993 – REVISED DECEMBER 2006 A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high or low logic levels) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus lines without interface or pullup components. OE does not affect internal operations of the latch. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. The outputs, which are designed to source or sink up to 12 mA, include equivalent 22- Ω series resistors to reduce overshoot and undershoot. Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. When VCC is between 0 and 1.5 V, the devices are in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.5 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the devices when they are powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. These devices can be used as two 8-bit latches or one 16-bit latch. When the latch-enable (LE) input is high, the Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs are latched at the levels set up at the D inputs. 1 2 3 4 5 6 A 1OE NC NC NC NC 1LE B 1Q2 1Q1 GND GND 1D1 1D2 C 1Q4 1Q3 VCC VCC 1D3 1D4 D 1Q6 1Q5 GND GND 1D5 1D6 E 1Q8 1Q7 1D7 1D8 F 2Q1 2Q2 2D2 2D1 G 2Q3 2Q4 GND GND 2D4 2D3 H 2Q5 2Q6 VCC VCC 2D6 2D5 J 2Q7 2Q8 GND GND 2D8 2D7 K 2OE NC NC NC NC 2LE (1) NC - No internal connection FUNCTION TABLE (each 8-bit section) INPUTS OUTPUT Q OE LE D L H H H L H L L L L X Q0 H X X Z 2 Submit Documentation Feedback |
Número de pieza similar - 74LVTH162373ZQLR |
|
Descripción similar - 74LVTH162373ZQLR |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |