Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
L6374 Datasheet(PDF) 9 Page - STMicroelectronics |
|
L6374 Datasheet(HTML) 9 Page - STMicroelectronics |
9 / 19 page L6374 Diagnostic logic 9/19 7 Diagnostic logic The situations that are monitored and signalled with the Diag output pin are: ● current limit (OVC) in action; there are 8 individual current limiting circuits, two per each output, i.e. one per every output transistor; they limit the current that can be either sour- ced or sunk from each output, to a typical value of 150 mA, equal for all of them; ● undervoltage protection (UV); ● overtemperature protection (OVP); The diagnostic signal is transmitted via an open drain output (for ease of wired-or connection of several such signals) and a low level represents the presence of at least one of the monitored conditions, mentioned above. 8 Programmable delay The current limiting circuits can be requested to perform even in absence of a real fault condition, for a short period, if the load is of capacitive nature or if it is a filament lamp (that exhibits a very low resistance during the initial heating phase). To avoid the forwarding of misleading, short diagnostic pulses in coincidence with the intervention of the current limiting circuits when operating on capacitive loads, a delay of about 5 µs is inserted on the signal path, between the "OR" of the current limit signals and its use as external diagnostic. It takes about 1 µs to charge (or discharge) by 24 V a capacitor of 5 nF with a current of 120 mA . To implement longer delays (from the intervention of one of the current limiting circuits to the activation of the diagnostic) an external capacitor can be connected between pin C3 and ground (pin C3 is otherwise left open). The delay shall then be determined by the ratio of about 10 pF/ µs, using the value of the capacitance connected to the pin. 9 Analog inputs (I1,I2,I3,I4) The input stage of each channel is a high im-pedence comparator with built-in hysteresis (200 mV) for high noise immunity. Each comparator has one input connected to all the others and tied to a common pin Ref (Pin 11). If this pin is left floating an internal precise band gap voltage reference (1.25 V) is applied, otherwise these inputs can be externally programmed by connecting an external voltage source (from 0 to 5 V) and the current on this pin is internally limited to ±20 mA. The other input pin of each comparator can swing from -7 to 35 V. For this reason it has been implemented the structure shown in Figure 4 on page 10 and the device can also be used as line receiver. When the input voltage is negative, the current is internally limited by a 15 k Ω resistor as shown in Figure 4 on page 10. High and low input thresholds can be obtained by adding and subtracting half of the hysteresis to the voltage of pin Ref (see Figure 5 on page 10). |
Número de pieza similar - L6374_08 |
|
Descripción similar - L6374_08 |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |