MC54/74HC4066A

MOTOROLA

High–Speed CMOS Logic Data

DL129 — Rev 6

2

MAXIMUM RATINGS*

Symbol

Parameter

Value

Unit

VCC

Positive DC Supply Voltage (Referenced to GND)

– 0.5 to + 14.0

V

VIS

Analog Input Voltage (Referenced to GND)

– 0.5 to VCC + 0.5

V

Vin

Digital Input Voltage (Referenced to GND)

– 0.5 to VCC + 0.5

V

I

DC Current Into or Out of Any Pin

± 25

mA

PD

Power Dissipation in Still Air, Plastic or Ceramic DIP†

SOIC Package†

TSSOP Package†

750

500

450

mW

Tstg

Storage Temperature

– 65 to + 150

_C

TL

Lead Temperature, 1 mm from Case for 10 Seconds

(Plastic DIP, SOIC or TSSOP Package)

(Ceramic DIP)

260

300

_C

* Maximum Ratings are those values beyond which damage to the device may occur.

Functional operation should be restricted to the Recommended Operating Conditions.

†Derating — Plastic DIP: – 10 mW/

_C from 65_ to 125_C

Ceramic DIP: – 10 mW/

_C from 100_ to 125_C

SOIC Package: – 7 mW/

_C from 65_ to 125_C

TSSOP Package: – 6.1 mW/

_C from 65_ to 125_C

For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

RECOMMENDED OPERATING CONDITIONS

Symbol

Parameter

Min

Max

Unit

VCC

Positive DC Supply Voltage (Referenced to GND)

2.0

12.0

V

VIS

Analog Input Voltage (Referenced to GND)

GND

VCC

V

Vin

Digital Input Voltage (Referenced to GND)

GND

VCC

V

VIO*

Static or Dynamic Voltage Across Switch

—

1.2

V

TA

Operating Temperature, All Package Types

– 55

+ 125

_C

tr, tf

Input Rise and Fall Time, ON/OFF Control

Inputs (Figure 10)

VCC = 2.0 V

VCC = 3.0 V

VCC = 4.5 V

VCC = 9.0 V

VCC = 12.0 V

0

0

0

0

0

1000

600

500

400

250

ns

* For voltage drops across the switch greater than 1.2 V (switch on), excessive VCC current may

be drawn; i.e., the current out of the switch may contain both VCC and switch input components.

The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.

Sb l

P

T

C

di i

V

Guaranteed Limit

Ui

Symbol

Parameter

Test Conditions

VCC

V

– 55 to

25

_C

v 85_C

v 125_C

Unit

VIH

Minimum High–Level Voltage

ON/OFF Control Inputs

Ron = Per Spec

2.0

3.0

4.5

9.0

12.0

1.5

2.1

3.15

6.3

8.4

1.5

2.1

3.15

6.3

8.4

1.5

2.1

3.15

6.3

8.4

V

VIL

Maximum Low–Level Voltage

ON/OFF Control Inputs

Ron = Per Spec

2.0

3.0

4.5

9.0

12.0

0.5

0.9

1.35

2.7

3.6

0.5

0.9

1.35

2.7

3.6

0.5

0.9

1.35

2.7

3.6

V

Iin

Maximum Input Leakage Current

ON/OFF Control Inputs

Vin = VCC or GND

12.0

± 0.1

± 1.0

± 1.0

µA

ICC

Maximum Quiescent Supply

Current (per Package)

Vin = VCC or GND

VIO = 0 V

6.0

12.0

2

4

20

40

40

160

µA

NOTE: Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

This device contains protection

circuitry to guard against damage

due to high static voltages or electric

fields. However, precautions must

be taken to avoid applications of any

voltage higher than maximum rated

voltages to this high–impedance cir-

cuit. For proper operation, Vin and

Vout should be constrained to the

range GND

v (Vin or Vout) v VCC.

Unused inputs must always be

tied to an appropriate logic voltage

level (e.g., either GND or VCC).

Unused outputs must be left open.

I/O pins must be connected to a

properly terminated line or bus.