SPECIFICATION

MODEL

DCVOLTAGE

RATEDCURRENT

CURRENTRANGE

RATEDPOWER

PEAKCURRENT

OUTPUT

VOLTAGE ADJ.RANGE

LINEREGULATION

LOADREGULATION

SETUP,RISETIME

HOLDUP TIME (Typ.)

VOLTAGERANGE

FREQUENCY RANGE

EFFICIENCY (Typ.)

Note.8

INPUT

INRUSHCURRENT (Typ.)

LEAKAGECURRENT

OVERTEMPERATURE

SAFETY STANDARDS

HARMONICCURRENT

EMSIMMUNITY

WORKINGTEMP.

Note.5

DCOKREALY CONTACTRATINGS(max.)

WORKINGHUMIDITY

STORAGETEMP.,HUMIDITY

TEMP.COEFFICIENT

VIBRATION

MTBF

DIMENSION

OTHERS

NOTE

PACKING

OVERLOAD

OVERVOLTAGE

ACCURRENT (Typ.)

1500ms,60ms/230VAC30

atfullload

00ms,60ms/115VAC

20ms/230VAC20ms/115VACatfullload

88~264VAC124~370VDC

47~63Hz

94%

0.93/230VAC0.99/115VACatfullload

2.6A/115VAC1.3A/230VAC

56~65V

33A/115VAC65A/230VAC

<1mA /240VAC

Normallyw

morethan3secandthenshutdowno/pvoltagewithauto-recovery

orkswithin110~150%ratedoutputpowerfor

29~33V

>150%ratedpower,constantcurrentlimitingwithauto-recoverywithin2secondsandmaycausetoshutdownifover2seconds

Protectiontype:Shutdowno/pvoltagewithauto-recovery

95

5

(TSW:detectonheatsinkofpowerswitch)

Protectiontype:Shutdowno/pvoltage,recoversautomaticallyaftertemperaturegoesdown

UL508 TUVEN60950-1approved

,

CompliancetoEN55022(CISPR22)ClassB

CompliancetoEN61000-3-2,-3

CompliancetoEN61000-4-2,3,4,5,6,8,11,ENV50204,EN55024,EN61000-6-2(EN50082-2),EN61204-3,heavyindustrylevel,

criteria A,SEMIF47,GL approved

-25~+70

(Refertooutputloadderatingcurve)

60Vdc/0.3A,30Vdc/1A,30Vac/0.5A resistiveload

20~95%RHnon-condensing

-20~+85

,10~95%RH

0.03%/

(0~50

Component:10~500Hz,2G10min./1cycle,60min.eachalongX, Y,Zaxes;Mounting:CompliancetoIEC60068-2-6

169.3Khrsmin.MIL-HDBK-217F(25

)

63*125.2*113.5mm(W*H*D)

1.03Kg;12pcs/13.4Kg/1.06CUFT

POWERFACTOR (Typ.)

SDR-240-48

48V

5A

0~5A

240W

7.5A

120mVp-p

48~55V

1.0%

0.5%

1.0%

SDR-240-24

24V

10A

0~10A

240W

15A

360W(3sec.)

100mVp-p

24~28V

1.0%

0.5%

1.0%

Features :

WITHSTANDVOLTAGE

ISOLATIONRESISTANCE

I/P-O/P:3KVACI/P-FG:1.5KVACO/P-FG:0.5KVAC

O/P-DCOK:0.5KVAC

I/P-O/P,I/P-FG,O/P-FG:>100MOhms/500VDC/25

/70%RH

EMICONDUCTION&RADIATION

ENVIRONMENT

SAFETY &

FUNCTION

EMC

(Note4)

PROTECTION

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25

of ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets

EMC directives.

5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.

In case the adjacent device is a heat source, 15mm clearance is recommended.

6. 3 seconds max., please refer to peak loading curves.

7. Derating may be needed under low input voltage. Please check the derating curve for more details.

8. After 30 min. of burn-in.

240WSingleOutputIndustrialDINRAIL withPFCFunction

Marine

GL

High efficiency 94% and low power dissipation

Built-in active PFC function, PF>0.93

Protections: Short circuit / Overload / Over voltage / Over temperature

Cooling by free air convection

Built-in constant current limiting circuit

Can be installed on DIN rail TS-35/7.5 or 15

UL 508 (industrial control equipment) approved

EN61000-6-2(EN50082-2) industrial immunity level

100% full load burn-in test

3 years warranty

150% peak load capability

Built-in DC OK relay contact

PQ

S

E

M

I F

4

7

FileName:SDR-240-SPEC2008-12-17