Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
CAT5221YI10 Datasheet(PDF) 2 Page - ON Semiconductor |
|
CAT5221YI10 Datasheet(HTML) 2 Page - ON Semiconductor |
2 / 16 page CAT5221 Doc. No. MD-2113 Rev. M 2 © 2009 SCILLC. All rights reserved. Characteristics subject to change without notice PIN DESCRIPTION Pin (SOIC) Name Function 1 RW0 Wiper Terminal for Potentiometer 0 2 RL0 Low Reference Terminal for Potentiometer 0 3 RH0 High Reference Terminal for Potentiometer 0 4 A0 Device Address, LSB 5 A2 Device Address 6 RW1 Wiper Terminal for Potentiometer 1 7 RL1 Low Reference Terminal for Potentiometer 1 8 RH1 High Reference Terminal for Potentiometer 1 9 SDA Serial Data Input/Output 10 GND Ground 11 NC No Connect 12 NC No Connect 13 NC No Connect 14 SCL Bus Serial Clock 15 A3 Device Address 16 A1 Device Address 17 NC No Connect 18 NC No Connect 19 NC No Connect 20 VCC Supply Voltage PIN DESCRIPTION SCL: Serial Clock The CAT5221 serial clock input pin is used to clock all data transfers into or out of the device. SDA: Serial Data The CAT5221 bidirectional serial data pin is used to transfer data into and out of the device. The SDA pin is an open drain output and can be wire-Or'd with the other open drain or open collector outputs. A0, A1, A2, A3: Device Address Inputs These inputs set the device address when addressing multiple devices. A total of sixteen devices can be addressed on a single bus. A match in the slave address must be made with the address input in order to initiate communication with the CAT5221. RH, RL: Resistor End Points The two sets of RH and RL pins are equivalent to the terminal connections on a mechanical potentiometer. RW: Wiper The two RW pins are equivalent to the wiper terminal of a mechanical potentiometer. DEVICE OPERATION The CAT5221 is two resistor arrays integrated with I 2C serial interface logic, two 6-bit wiper control registers and eight 6-bit, non-volatile memory data registers. Each resistor array contains 63 separate resistive elements connected in series. The physical ends of each array are equivalent to the fixed terminals of a mechanical potentiometer (RH and RL). RH and RL are symmetrical and may be interchanged. The tap positions between and at the ends of the series resis– tors are connected to the output wiper terminals (RW) by a CMOS transistor switch. Only one tap point for each potentiometer is connected to its wiper terminal at a time and is determined by the value of the wiper control register. Data can be read or written to the wiper control registers or the non-volatile memory data registers via the I 2C bus. Additional instructions allow data to be transferred between the wiper control registers and each respective potentiometer's non-volatile data registers. Also, the device can be instructed to operate in an "increment/decrement" mode. |
Número de pieza similar - CAT5221YI10 |
|
Descripción similar - CAT5221YI10 |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |