Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
ADP2120ACPZ-1.8-R7 Datasheet(PDF) 6 Page - Analog Devices |
|
ADP2120ACPZ-1.8-R7 Datasheet(HTML) 6 Page - Analog Devices |
6 / 24 page ADP2119/ADP2120 Rev. 0 | Page 6 of 24 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 10 EN ADP2119/ADP2120 EXPOSED PAD 1 VIN 9 SYNC/MODE 2 PVIN 8 PGOOD 3 SW 7 TRK 4 PGND 6 FB 5 GND NOTES 1. THE EXPOSED PAD SHOULD BE SOLDERED TO AN EXTERNAL GROUND PLANE UNDERNEATH THE IC FOR THERMAL DISSIPATION. Figure 3. Pin Configuration (Top View) Table 4. Pin Function Descriptions Pin No. Mnemonic Description 1 VIN Bias Voltage Input Pin. Connect a bypass capacitor (0.1 μF minimum) between this pin and GND and a small (10 Ω) resistor between this pin and PVIN. 2 PVIN Power Input Pin. Connect this pin to the input power source. Connect a bypass capacitor between this pin and PGND. 3 SW Switch Node Output. Connect this pin to the output inductor. 4 PGND Power Ground. Connect this pin to the power ground plane and to the high current return for the power MOSFET. 5 GND Analog Ground. Connect this pin to the ground plane. 6 FB Feedback Voltage Sense Input. Connect this pin to a resistor divider from VOUT. For the fixed output version, connect to VOUT directly. 7 TRK Tracking Input. To track a master voltage, drive TRK from a resistor divider from the master voltage. If the tracking function is not used, connect TRK to VIN. 8 PGOOD Power-Good Output (Open Drain). Connect this pin to a resistor to any pull-up voltage < 5.5 V. 9 SYNC/MODE Synchronization Input (SYNC). Connect this pin to an external clock between 1 MHz and 2 MHz to synchronize the switching frequency to the external clock (see the Oscillator and Synchronization section for details). FPWM/PFM Selection (MODE). When this pin is connected to VIN, the PFM mode is disabled and the part works in continuous conduction mode (CCM) only. When this pin is connected to ground, the PFM mode is enabled and becomes active at light loads. 10 EN Precision Threshold Enable Input Pin. An external resistor divider can be used to set the turn-on threshold. To enable the part automatically, connect the EN pin to VIN. This pin has a 1 MΩ pull-down resistor to GND. EPAD Exposed Pad The exposed pad should be soldered to an external ground plane underneath the IC for thermal dissipation. |
Número de pieza similar - ADP2120ACPZ-1.8-R7 |
|
Descripción similar - ADP2120ACPZ-1.8-R7 |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |