Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
TSM-110-01-T-DVP Datasheet(PDF) 8 Page - Texas Instruments |
|
TSM-110-01-T-DVP Datasheet(HTML) 8 Page - Texas Instruments |
8 / 32 page ADS7953EVM-PDK Kit Operation www.ti.com 7 ADS7953EVM-PDK Kit Operation This section provides information on using the ADS7953EVM-PDK, including setup, program installation, and program usage. To prepare to evaluate the ADS7953 with the ADS7953EVM-PDK, complete the following steps: Step 1. Install the ADCPro software (if not already installed) on a PC. Step 2. Install the ADS7953EVM-PDK EVM plug-in software. Step 3. Set up the ADS7953EVM-PDK. Step 4. Connect a proper power supply or use the included AC adapter. Step 5. Complete the NI-VISA USB driver installation process. Step 6. Run the ADCPro software. Step 7. Complete the Microsoft Windows USB driver installation process. Each task is described in the subsequent sections of this document. 7.1 Installing the ADCPro Software CAUTION Do not connect the ADS7953EVM-PDK before installing the software on a suitable PC. Failure to observe this caution may cause Microsoft Windows to not recognize the ADS7953EVM-PDK. The latest software is available from the TI website at http://www.ti.com/. The ADCPro installer will check for updates when executed (if connected to the Internet), and then gives the option of downloading and installing the latest version. See the ADCPro Analog-to-Digital Converter Evalutation Software Users Guide for instructions on installing and using ADCPro. To install the ADS7953EVM-PDK plug-in, run the file: ads7953evm-pdk-plugin-1.1.0.exe (1.1.0 is the version number, and increments with software version releases). Double-click the file to run it; then follow the instructions shown. Also, use the ADCPro Update Check feature to check for newer versions of the ADS7953EVM-PDK plug-in, once one version has been installed. The software should now be installed, but the USB drivers may not have been loaded by the PC operating system. This step will complete when the ADCPro software is executed. 7.2 Setting Up the ADS7953EVM-PDK The ADS7953EVM-PDK contains both the ADS7953EVM and the MMB0 motherboard; however, the devices are shipped unconnected. Follow these steps to set up the ADS7953EVM-PDK: Step 1. Unpack the ADS7953EVM-PDK kit. Step 2. Set the jumpers and switches on the MMB0 as shown in Figure 3. • Set the Boot Mode switch to USB. • Connect +5V and +5VA on jumper block J13 (if +5V is supplied from J14 +5VA). • Leave +5V and +VA disconnected on jumper block J13. • If the PDK will be powered from an ac adapter, connect J12. If the PDK will be powered through the terminal block, disconnect J12 (see Section 7.3 of this document for additional power supply connection details). 8 ADS79xxEVM and ADS79xxEVM-PDK SLAU262C – January 2009 – Revised May 2011 Submit Documentation Feedback Copyright © 2009–2011, Texas Instruments Incorporated |
Número de pieza similar - TSM-110-01-T-DVP |
|
Descripción similar - TSM-110-01-T-DVP |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |