Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
ADG752BRT Datasheet(PDF) 4 Page - Analog Devices |
|
ADG752BRT Datasheet(HTML) 4 Page - Analog Devices |
4 / 8 page REV. 0 ADG752 –4– Table I. Truth Table ADG752 IN Switch S1 Switch S2 0 ON OFF 1 OFF ON CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADG752 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE ABSOLUTE MAXIMUM RATINGS 1 (TA = +25°C unless otherwise noted) VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V Analog, Digital Inputs2 . . . . . . . . . . . . –0.3 V to VDD +0.3 V or 30 mA, Whichever Occurs First Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . .100 mA (Pulsed at 1 ms, 10% Duty Cycle Max) Continuous Current, S or D . . . . . . . . . . . . . . . . . . . . . 30 mA Operating Temperature Range Industrial (B Version) . . . . . . . . . . . . . . . . . –40 °C to +85°C Storage Temperature Range . . . . . . . . . . . . . –65 °C to +150°C Power Dissipation . . . . . . . . . . . . . . . . . . . . . (TJ Max–TA)/ θJA Junction Temperature (TJ Max) . . . . . . . . . . . . . . . . . .+150 °C µSOIC Package θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 206°C/W θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . 44°C/W SOT-23 Package θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 229.6°C/W θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . 91.99°C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . . +215 °C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+220 °C NOTES 1Stresses above those listed under Absolute Maximum Ratings may cause perma- nent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating condi- tions for extended periods may affect device reliability. Only one absolute maxi- mum rating may be applied at any one time. 2Overvoltages at IN, S or D will be clamped by internal diodes. Current should be limited to the maximum ratings given. ORDERING GUIDE Model Temperature Range Brand* Package Descriptions Package Options ADG752BRM –40 °C to +85°C SEB µSOIC RM-8 ADG752BRT –40 °C to +85°C SEB SOT-23 RT-6 *Brand on these packages is limited to three characters due to space constraints. TERMINOLOGY VDD Most positive power supply potential. GND Ground (0 V) reference. S Source terminal. May be an input or output. D Drain terminal. May be an input or output. IN Logic control input. RON Ohmic resistance between D and S. ∆RON On resistance match between channels, i.e., RONmax–RONmin. RFLAT(ON) Flatness is defined as the difference between the maximum and minimum value of on resis- tance as measured over the specified analog signal range. IS (OFF) Source leakage current with the switch “OFF.” ID, IS (ON) Channel leakage current with the switch “ON.” VD (VS) Analog voltage on terminals D and S. CS (OFF) “OFF” switch source capacitance. CD, CS (ON) “ON” switch capacitance. tON Delay between applying the digital control input and the output switching on. See Test Circuit 4. tOFF Delay between applying the digital control input and the output switching off. tD “OFF” time or “ON” time measured between the 90% points of both switches, when switch- ing from one address state to another. Off Isolation A measure of unwanted signal coupling through an “OFF” switch. Crosstalk A measure of unwanted signal that is coupled through from one channel to another as a result of parasitic capacitance. Bandwidth The frequency at which the output is attenu- ated by –3 dBs. On Response The frequency response of the “ON” switch. Insertion Loss Loss due to the ON resistance of the switch. VINL Maximum input voltage for Logic “0.” VINH Minimum input voltage for Logic “1.” IINL(IINH) Input current of the digital input. IDD Positive supply current. PIN CONFIGURATIONS 6-Lead SOT-23 (RT-6) 1 2 3 6 5 4 TOP VIEW (Not to Scale) ADG752 IN D VDD S1 GND S2 8-Lead SOIC (RM-8) 1 2 3 4 8 7 6 5 TOP VIEW (Not to Scale) NC = NO CONNECT ADG752 NC NC S1 D VDD S2 GND IN |
Número de pieza similar - ADG752BRT |
|
Descripción similar - ADG752BRT |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |