 |
Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
|
Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
MCP4441T-503EML Datasheet(PDF) 11 Page - Microchip Technology |
|
||||||||||||||||||||||||||||||
MCP4441T-503EML Datasheet(HTML) 11 Page - Microchip Technology |
|
|
11 / 100 page  © 2010 Microchip Technology Inc. DS22265A-page 11 MCP444X/446X Weak Pull-up Current IPU — — 1.75 mA Internal VDD pull-up, VIHH pull-down, VDD = 5.5V, VHVC = 12.5V — 170 — µA HVC pin, VDD = 5.5V, VHVC = 3V HVC Pull-up / Pull-down Resistance RHVC —16 — k Ω VDD = 5.5V, VHVC = 3V RESET Pull-up Resistance RRESET —16 — k Ω VDD = 5.5V, VRESET = 0V Input Leakage Current IIL -1 — 1 µA VIN = VDD (all pins) and VIN = VSS (all pins except RESET) Pin Capacitance CIN, COUT —10 — pF fC = 20 MHz RAM (Wiper, TCON) Value Value Range N 0h — 1FFh hex 8-bit device 0h — 1FFh hex 7-bit device TCON POR/BOR Setting 1FF hex All Terminals connected EEPROM Endurance Endurance —1M — Cycles EEPROM Range N 0h — 1FFh hex Initial NV Wiper POR/BOR Setting N 080h hex 8-bit WiperLock Technology = Off 040h hex 7-bit WiperLock Technology = Off Initial EEPROM POR/BOR Setting N 000h hex EEPROM Programming Write Cycle Time tWC —3 10 ms Power Requirements Power Supply Sensitivity (MCP44X1) PSS — 0.0015 0.0035 %/% 8-bit VDD = 2.7V to 5.5V, VA = 2.7V, Code = 80h — 0.0015 0.0035 %/% 7-bit VDD = 2.7V to 5.5V, VA = 2.7V, Code = 40h AC/DC CHARACTERISTICS (CONTINUED) DC Characteristics Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C ≤ TA ≤ +125°C (extended) All parameters apply across the specified operating ranges unless noted. VDD = +2.7V to 5.5V, 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ devices. Typical specifications represent values for VDD = 5.5V, TA = +25°C. Parameters Sym Min Typ Max Units Conditions Note 1: Resistance is defined as the resistance between terminal A to terminal B. 2: INL and DNL are measured at VW with VA = VDD and VB = VSS. 3: MCP44X1 only. 4: MCP44X2 only, includes VWZSE and VWFSE. 5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted. 6: This specification by design. 7: Non-linearity is affected by wiper resistance (RW), which changes significantly over voltage and temperature. 8: The MCP44X1 is externally connected to match the configurations of the MCP44X2, and then tested. 9: POR/BOR is not rate dependent. 10: Supply current is independent of current through the resistor network. 11: When HVC/A0 = VIHH, the IDD current is less due to current into the HVC/A0 pin. See IPU specification. |
Número de pieza similar - MCP4441T-503EML |
|
Descripción similar - MCP4441T-503EML |
|
|
Enlace URL |
| Política de Privacidad |
| ALLDATASHEET.ES |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Spanish ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
