Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
LM5041 Datasheet(PDF) 11 Page - Texas Instruments |
|
|
LM5041 Datasheet(HTML) 11 Page - Texas Instruments |
11 / 22 page K1 * RSET PUSH DEADTIME WAVEFORMS PULL PUSH PULL K1 * RSET K2 * RSET K2 * RSET OVERLAP WAVEFORMS LM5041 www.ti.com SNVS248D – AUGUST 2003 – REVISED MARCH 2013 Push-Pull Outputs The push pull outputs operate continuously at a nominal 50% duty cycle. A distinguishing feature of the LM5041 is the ability to accurately configure either dead time (both-off) or overlap time (both-on) on the complementary push-pull outputs. The overlap/dead time magnitude is controlled by a resistor connected to the TIME pin on the controller. The TIME pin holds one end of the resistor at 2.5V and the other end of the resistor should be connected to either REF for dead time control setting or to GND for overlap control. The polarity of the current in the TIME is detected by the LM5041 The magnitude of the overlap/dead time can be calculated as follows: • Overlap Time (ns) = (3.66 x RSET) + 7 • Overlap Time in ns, RSET connected to GND, RSET in kΩ • Dead Time (ns) = (3.69 x RSET) + 21 • Dead Time in ns, RSET connected to REF, RSET in kΩ • Recommended RSET programming range: 10kΩ to 100kΩ Current-fed designs require a period of overlap to insure there is a continuous path for the buck inductor current. Voltage-fed designs require a period of dead time to insure there is no time when the push-pull transformer acts as a shorted turn to the low impedance sourcing node. The push-pull outputs alternate continuously under all conditions provided REF the voltage is greater than 3V. PWM Comparator The PWM comparator compares the slope compensated current ramp signal to the loop error voltage from the internal error amplifier (COMP pin). This comparator is optimized for speed in order to achieve minimum controllable duty cycles. The comparator polarity is such that 0V on the COMP pin will produce zero duty cycle in the buck stage. Error Amplifier An internal high gain wide-bandwidth error amplifier is provided within the LM5041. The amplifier’s non-inverting input is tied to a 0.75V reference. The inverting input is connected to the FB pin. In non-isolated applications the power converter output is connected to the FB pin via the voltage setting resistors. Loop compensation components are connected between the COMP and FB pins. For most isolated applications the error amplifier function is implemented on the secondary side of the converter and the internal error amp is not used. The internal error amplifier is configured as an open drain output and can be disabled by connecting the FB pin to ground. An internal 5k Ω pull-up resistor between the 5V reference and COMP can be used as the pull-up for an opto-coupler in isolated applications. Copyright © 2003–2013, Texas Instruments Incorporated Submit Documentation Feedback 11 Product Folder Links: LM5041 |
Número de pieza similar - LM5041 |
|
Descripción similar - LM5041 |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |