Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
CAR2024FPBZ01A Datasheet(PDF) 5 Page - Lineage Power Corporation |
|
CAR2024FPBZ01A Datasheet(HTML) 5 Page - Lineage Power Corporation |
5 / 7 page GE Energy CAR2024FP series rectifier Input: 90Vac to 264Vac; Output: 24Vdc @ 83A; 3.3Vdc or 5 Vdc @ 1A March 28, 2013 ©2012 General Electric Company. All rights reserved. Page 5 AC OK: A TTL compatible status signal representing whether the input voltage is within the anticipated range. This signal needs to be pulled HI externally through a resistor. Maximum sink current ≤ 4mA and the max voltage is 12Vdc. Open collector (HI) on this signal indicates that the input voltage is applied within the specified input range. DC OK: A TTL compatible status signal representing whether the output voltage is present. This signal needs to be pulled HI externally through a resistor. Maximum sink current ≤ 4mA and the max voltage is 12Vdc. Open collector (HI) on this signal indicates that the output voltage is present. Over temp warning: A TTL compatible status signal representing whether an over temperature exists. This signal needs to be pulled HI externally through a resistor. Maximum sink current ≤ 4mA and the max voltage is 12Vdc. Open collector (HI) on this signal indicates that temperatures are normal. If an over temperature should occur, this signal would pull LO for approximately 10 seconds prior to shutting down the power supply. The unit would restart if internal temperatures recover within normal operational levels. At that time the signal reverts back to its open collector (HI) state. Fault: A TTL compatible status signal representing whether a Fault occurred. This signal needs to be pulled HI externally through a resistor. Maximum sink current ≤ 4mA and the max voltage is 12Vdc. Open collector (HI) on this signal indicates that no Fault is present. This signal activates for OTP, OVP, OCP, AC fault or No output. PS Present: This pin is connected to ‘output return’ within the power supply. Its intent is to indicate to the system that a power supply is present. This signal may need to be pulled HI externally through a resistor. Interrupt (SMBAlert): A TTL compatible status signal, representing the SMBusAlert# feature of the PMBus compatible i 2C protocol in the power supply. This signal needs to be pulled HI externally through a resistor. Maximum sink current ≤ 4mA and the pull up resistor should be tied to 3.3Vdc. Open collector (HI) on this signal indicates that no Interrupt has been triggered. Serial Bus Communications The I²C interface facilitates the monitoring and control of various operating parameters within the unit and transmits these on demand over an industry standard I²C Serial bus. All signals are referenced to ‘Signal Return’. Device addressing: The microcontroller (MCU) and the EEPROM have the following addresses: Device Address Address Bit Assignments (Most to Least Significant) MCU 0xBx 1 0 1 1 A2 A1 A0 R/W EEPROM 0xAx 1 0 1 0 A2 A1 A0 R/W Address lines (A2, A1, A0): These signal pins allow up to eight (8) modules to be addressed on a single I²C bus. The pins are pulled HI internal to the power supply. For a logic LO these pins should be connected to ‘Output Return’ Serial Clock (SCL): The clock pulses on this line are generated by the host that initiates communications across the I²C Serial bus. This signal is pulled up internally to 3.3V by a 10kΩ resistor. The end user should add additional pull up resistance as necessary to ensure that rise and fall time timing and the maximum sink current is in compliance to the I²C specifications. Serial Data (SDA): This line is a bi-directional data line. . This signal is pulled up internally to 3.3V by a 10kΩ resistor. The end user should add additional pull up resistance as necessary to ensure that rise and fall time timing and the maximum sink current is in compliance to the I²C specifications. EEPROM The microcontroller has 96 bytes of EEPROM memory available for the system host. Another separate EEPROM IC will provide another 128 bytes of memory with write protect feature. Minimum information to be included in this separate EEPROM: model number, revision, date code, serial number etc. See the communications protocol for further information. Communications Protocol The I²C protocol is described in detail by the I 2C and PMBus Serial Communications Protocol for the CAR Family of Power Supplies application note. The following I²C protocol commands are not supported: FAN1_SPEED_ I²C, FAN2_SPEED_ I²C VIN_ I²C, IIN_ I²C, PIN_ I²C The following PMBus protocol commands are not supported: FAN_COMMAND_1 0 x 21 STATUS_FAN_1_2 0 x 81 READ_VIN 0 x 88 READ_IIN 0 x 89 READ_FAN_SPEED_1 0 x 90 READ_FAN_SPEED_2 0 x 91 READ_PIN 0 x A3 The STAUS_MFR_SPECIFIC (Register 0 x 80) has a bit changed; Bit 5 0 = interrupt, 1 = no interrupt |
Número de pieza similar - CAR2024FPBZ01A |
|
Descripción similar - CAR2024FPBZ01A |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |