Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
MAX232E Datasheet(PDF) 9 Page - Maxim Integrated Products |
|
MAX232E Datasheet(HTML) 9 Page - Maxim Integrated Products |
9 / 25 page Maxim Integrated | 9 www.maximintegrated.com MAX202E–MAX213E, MAX232E/MAX241E ±15kV ESD-Protected, 5V RS-232 Transceivers V+ MAX2_ _E 0.1 μF* VCC 0.1 μF* T_ R_ 0.1 μF* C1+ C1- C2+ C2- VCC T_OUT R_OUT EN (EN) SHDN (SHDN) 400k Ω 5k Ω 0.1 μF* 0.1 μF* 3k Ω +5V R_IN T_IN MINIMUM SLEW-RATE TEST CIRCUIT 0V (+5V) 0V (+5V) 2500pF V- V+ 0.1 μF* VCC 0.1 μF* R_ T_ 0.1 μF* C1+ C1- C2+ C2- VCC T_OUT R_OUT EN (EN) SHDN (SHDN) 400k Ω 5k Ω 0.1 μF* 0.1 μF* 7k Ω +5V R_IN T_IN MAXIMUM SLEW-RATE TEST CIRCUIT 0V (+5V) 0V (+5V) 50pF V- ( ) ARE FOR MAX213E * 1 μF FOR MAX232E/MAX241E MAX2_ _E TRANSMITTER INPUT PULL-UP RESISTORS, ENABLE, AND SHUTDOWN ARE NOT PROVIDED ON THE MAX202E, MAX203E, AND MAX232E. ENABLE AND SHUTDOWN ARE NOT PROVIDED ON THE MAX207E AND MAX208E. Figure 3. Transition Slew-Rate Circuit Detailed Description The MAX202E–MAX213E, MAX232E/MAX241E consist of three sections: charge-pump voltage converters, dri- vers (transmitters), and receivers. These E versions provide extra protection against ESD. They survive ±15kV discharges to the RS-232 inputs and outputs, tested using the Human Body Model. When tested according to IEC1000-4-2, they survive ±8kV contact- discharges and ±15kV air-gap discharges. The rugged E versions are intended for use in harsh environments or applications where the RS-232 connection is fre- quently changed (such as notebook computers). The standard (non-“E”) MAX202, MAX203, MAX205– MAX208, MAX211, MAX213, MAX232, and MAX241 are recommended for applications where cost is critical. +5V to ±10V Dual Charge-Pump Voltage Converter The +5V to ±10V conversion is performed by dual charge-pump voltage converters (Figure 4). The first charge-pump converter uses capacitor C1 to double the +5V into +10V, storing the +10V on the output filter capacitor, C3. The second uses C2 to invert the +10V into -10V, storing the -10V on the V- output filter capaci- tor, C4. In shutdown mode, V+ is internally connected to VCC by a 1kΩ pull-down resistor, and V- is internally connected to ground by a 1kΩ pull up resistor. RS-232 Drivers With VCC = 5V, the typical driver output voltage swing is ±8V when loaded with a nominal 5kΩ RS-232 receiv- er. The output swing is guaranteed to meet EIA/TIA- 232E and V.28 specifications that call for ±5V minimum output levels under worst-case conditions. These include a 3kΩ load, minimum VCC, and maximum oper- ating temperature. The open-circuit output voltage swings from (V+ - 0.6V) to V-. Input thresholds are CMOS/TTL compatible. The unused drivers’ inputs on the MAX205E–MAX208E, MAX211E, MAX213E, and MAX241E can be left uncon- nected because 400kΩ pull up resistors to VCC are included on-chip. Since all drivers invert, the pull up resistors force the unused drivers’ outputs low. The MAX202E, MAX203E, and MAX232E do not have pull up resistors on the transmitter inputs. |
Número de pieza similar - MAX232E |
|
Descripción similar - MAX232E |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |