Motor de Búsqueda de Datasheet de Componentes Electrónicos
Selected language     Spanish  ▼

Delete All
ON OFF
ALLDATASHEET.ES

X  

Preview PDF Download HTML

COP8ACC5 Datasheet(PDF) 11 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
No. de Pieza. COP8ACC5
Descripción  8-Bit CMOS ROM Based Microcontrollers with 4k Memory and High Resolution A/D
Descarga  41 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Fabricante  NSC [National Semiconductor (TI)]
Página de inicio  http://www.national.com
Logo 

COP8ACC5 Datasheet(HTML) 11 Page - National Semiconductor (TI)

Zoom Inzoom in Zoom Outzoom out
 11 / 41 page
background image
Pin Descriptions
V
CC and GND are the power supply pins. All VCC and GND
pins must be connected.
CKI is the clock input. This can come from an R/C generated
oscillator, or a crystal oscillator (in conjunction with CKO).
See Oscillator Description section.
RESET is the master reset input. See Reset description sec-
tion.
The device contains two bidirectional (one 8-bit, one 4-bit)
I/O ports (G and L), where each individual bit may be inde-
pendently configured as a weak pullup input, TRI-STATE®
(Hi-Z) input or push pull output under program control. Ports
G- and L- feature Schmitt trigger inputs. Three data memory
address locations are allocated for each of these I/O ports.
Each I/O port has two associated 8-bit memory mapped reg-
isters, the CONFIGURATION register and the output DATA
register. A memory mapped address is also reserved for the
input pins of each I/O port. (See the memory map for the
various addresses associated with the I/O ports.)
Figure 5
shows the I/O port configurations. The DATA and CONFIGU-
RATION registers allow for each port bit to be individually
configured under software control as shown below:
PORT L is a 4-bit I/O port. All L-pins have Schmitt triggers on
the inputs.
The Port L supports Multi-Input Wake Up on all four pins.
The Port L has the following alternate features:
L7
MIWU or external interrupt
L6
MIWU or external interrupt
L5
MIWU or external interrupt
L4
MIWU or external interrupt
Configuration
Data
Port Set-Up
Register
Register
0
0
Hi-Z Input (TRI-STATE Output)
0
1
Input with Weak Pull-Up
1
0
Push-Pull Zero Output
1
1
Push-Pull One Output
Please note:
The lower 4 L-bits read all ones (L0:L3). This is independant
from the states of the associated bits in the L-port Data- and
Configuration register. The lower 4 bits in the L-port Data-
and Configuration register can be used as general purpose
status indicators (flags).
Port G is an 8-bit port with 5 I/O pins (G0, G2–G5), an input
pin (G6), and a dedicated output pin (G7). Pins G0 and
G2–G6 all have Schmitt Triggers on their inputs. Pin G1
serves as the dedicated WDOUT WATCHDOG output, while
pin G7 is either input or output depending on the oscillator
mask option selected. With the crystal oscillator option se-
lected, G7 serves as the dedicated output pin for the CKO
clock output. With the single-pin R/C oscillator mask option
selected, G7 serves as a general purpose input pin but is
also used to bring the device out of HALT mode with a low to
high transition on G7. There are two registers associated
with the G Port, a data register and a configuration register.
Therefore, each of the 5 I/O bits (G0, G2–G5) can be indi-
vidually configured under software control.
Since G6 is an input only pin and G7 is the dedicated CKO
clock output pin (crystal clock option) or general purpose in-
put (R/C clock option), the associated bits in the data and
configuration registers for G6 and G7 are used for special
purpose functions as outlined below. Reading the G6 and G7
data bits will return zeros.
Note that the chip will be placed in the HALT mode by writing
a “1” to bit 7 of the Port G Data Register. Similarly the chip
will be placed in the IDLE mode by writing a “1” to bit 6 of the
Port G Data Register.
Writing a “1” to bit 6 of the Port G Configuration Register en-
ables the MICROWIRE/PLUS to operate with the alternate
phase of the SK clock. The G7 configuration bit, if set high,
enables the clock start up delay after HALT when the R/C
clock configuration is used.
Config Reg.
Data Reg.
G7
CLKDLY
HALT
G6
Alternate SK
IDLE
Port G has the following alternate features:
G6
SI (MICROWIRE Serial Data Input)
G5
SK (MICROWIRE Serial Clock)
G4
SO (MICROWIRE Serial Data Output)
G3
T1A (Timer T1 I/O)
G2
T1B (Timer T1 Capture Input)
G0
INTR (External Interrupt Input)
Port G has the following dedicated functions:
G7
CKO Oscillator dedicated output or general purpose
input
G1
WDOUT WATCHDOG and/or Clock Monitor dedicated
output.
Port I is an eight-bit Hi-Z input port.
Port I0–I7 are used for the analog function block.
The Port I has the following alternate features:
I7
C
OUT (Comparator Output)
I6
Analog CH6 (Comparator Positive Input 6)
I5
Analog CH5 (Comparator Positive Input 5)
I4
Analog CH4 (Comparator Positive Input 4)
I3
Analog CH3 (Comparator Positive Input 3/Comparator
Output)
I2
Analog CH2 (Comparator Positive Input 2)
I1
I
SRC (Comparator Negative Input/Current Source Out)
I0
Analog CH1 (Comparator Positive Input 1)
Port D is a 4-bit output port that is preset high when RESET
goes low. The user can tie two or more D port outputs (ex-
cept D2) together in order to get a higher drive.
DS012865-5
FIGURE 5. I/P Port Configurations
www.national.com
11


Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38  39  40  41 


Datasheet Download



Número de Pieza relacionado

Part NumberComponents DescriptionHtml ViewManufacturer
COP8ACC8-Bit CMOS ROM Based and OTP Microcontrollers with 4k or 16k Memory and High Resolution A/D 1 2 3 4 5 MoreNational Semiconductor (TI)
COP8FG8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory Two Comparators and USART 1 2 3 4 5 MoreNational Semiconductor (TI)
COP8SE8-Bit CMOS ROM Based and OTP Microcontrollers with 4k Memory and 128 Bytes EERAM 1 2 3 4 5 MoreNational Semiconductor (TI)
COP8SG8-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory Two Comparators and USART 1 2 3 4 5 MoreNational Semiconductor (TI)
COP8SGR728M88-Bit CMOS ROM Based and OTP Microcontrollers with 8k to 32k Memory Two Comparators and USART 1 2 3 4 5 MoreNational Semiconductor (TI)
COP884BC8-Bit CMOS ROM Based Microcontrollers with 2k Memory Comparators and CAN Interface 1 2 3 4 5 MoreNational Semiconductor (TI)
COP888CF8-Bit CMOS ROM Based Microcontrollers with 4k Memory and A/D Converter 1 2 3 4 5 MoreNational Semiconductor (TI)
COP888EB8-Bit CMOS ROM Based Microcontrollers with 8k Memory CAN Interface 8-Bit A/D and USART 1 2 3 4 5 MoreNational Semiconductor (TI)
COP888EK8-Bit CMOS ROM Based Microcontrollers with 8k Memory Comparator and Single-slope A/D Capability 1 2 3 4 5 MoreNational Semiconductor (TI)
COP888FH8-Bit CMOS ROM Based Microcontrollers with 12k Memory Comparators USART and Hardware Multiply/Divide 1 2 3 4 5 MoreNational Semiconductor (TI)

Enlace URL




Privacy Policy
ALLDATASHEET.ES
Does ALLDATASHEET help your business so far?  [ DONATE ]  

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Favorito   |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn