SN74CBT6800A

10-BIT FET BUS SWITCH

WITH PRECHARGED OUTPUTS

SCDS005N – MARCH 1993 – REVISED MARCH 2001

2

POST OFFICE BOX 655303

logic diagram (positive logic)

ON

A1

A10

B1

BIASV

B10

2

11

1

13

23

14

–0.5 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Bias voltage range, BIASV

–0.5 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–0.5 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Continuous channel current

128 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–50 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Package thermal impedance,

63

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DBQ package

61

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DGV package

86

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DW package

46

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PW package

88

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.

2. The package thermal impedance is calculated in accordance with JESD 51-7.

recommended operating conditions (see Note 3)

MIN

MAX

UNIT

VCC

Supply voltage

4

5.5

V

BIASV

Supply voltage

1.3

VCC

V

VIH

High-level control input voltage

2

V

VIL

Low-level control input voltage

0.8

V

TA

Operating free-air temperature

–40

85

°C

NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,

Implications of Slow or Floating CMOS Inputs, literature number SCBA004.