 |
Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
|
Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
LM4910MA Datasheet(PDF) 11 Page - National Semiconductor (TI) |
|
|
||||||||||||||||||||||||||||||
LM4910MA Datasheet(HTML) 11 Page - National Semiconductor (TI) |
|
|
11 / 22 page  Application Information (Continued) headphone operation (32 Ω impedance) using a 3.3V supply the maximum power dissipation is only 138mW. Therefore, power dissipation is not a major concern. POWER SUPPLY BYPASSING As with any amplifier, proper supply bypassing is important for low noise performance and high power supply rejection. The capacitor location on the power supply pins should be as close to the device as possible. Typical applications employ a 3.3V regulator with 10µF tan- talum or electrolytic capacitor and a ceramic bypass capaci- tor which aid in supply stability. This does not eliminate the need for bypassing the supply nodes of the LM4910. A bypass capacitor value in the range of 0.1µF to 1µF is recommended for C S. MICRO POWER SHUTDOWN The voltage applied to the SHUTDOWN pin controls the LM4910’s shutdown function. Activate micro-power shut- down by applying a logic-low voltage to the SHUTDOWN pin. When active, the LM4910’s micro-power shutdown fea- ture turns off the amplifier’s bias circuitry, reducing the sup- ply current. The trigger point is 0.4V(max) for a logic-low level, and 1.5V(min) for a logic-high level. The low 0.1µA(typ) shutdown current is achieved by applying a voltage that is as near as ground as possible to the SHUTDOWN pin. A volt- age that is higher than ground may increase the shutdown current. There are a few ways to control the micro-power shutdown. These include using a single-pole, single-throw switch, a microprocessor, or a microcontroller. When using a switch, connect an external 100k Ω pull-up resistor between the SHUTDOWN pin and V DD. Connect the switch between the SHUTDOWN pin and ground. Select normal amplifier opera- tion by opening the switch. Closing the switch connects the SHUTDOWN pin to ground, activating micro-power shut- down. The switch and resistor guarantee that the SHUT- DOWN pin will not float. This prevents unwanted state changes. In a system with a microprocessor or microcontrol- ler, use a digital output to apply the control voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin with active circuitry eliminates the pull-up resistor. SELECTING EXTERNAL COMPONENTS Selecting proper external components in applications using integrated power amplifiers is critical to optimize device and system performance. While the LM4910 is tolerant of exter- nal component combinations, consideration to component values must be used to maximize overall system quality. The LM4910 is unity-gain stable which gives the designer maximum system flexibility. The LM4910 should be used in low gain configurations to minimize THD+N values, and maximize the signal to noise ratio. Low gain configurations require large input signals to obtain a given output power. Input signals equal to or greater than 1V rms are available from sources such as audio codecs. Very large values should not be used for the gain-setting resistors. Values for R i and Rf should be less than 1M Ω. Please refer to the section, Audio Power Amplifier Design, for a more com- plete explanation of proper gain selection Besides gain, one of the major considerations is the closed- loop bandwidth of the amplifier. To a large extent, the band- width is dictated by the choice of external components shown in Figure 1. The input coupling capacitor, C i, forms a first order high pass filter which limits low frequency re- sponse. This value should be chosen based on needed frequency response and turn-on time. SELECTION OF INPUT CAPACITOR SIZE Amplifiying the lowest audio frequencies requires a high value input coupling capacitor, C i. A high value capacitor can be expensive and may compromise space efficiency in por- table designs. In many cases, however, the headphones used in portable systems have little ability to reproduce signals below 60Hz. Applications using headphones with this limited frequency response reap little improvement by using a high value input capacitor. In addition to system cost and size, turn-on time is affected by the size of the input coupling capacitor Ci. A larger input coupling capacitor requires more charge to reach its quies- cent DC voltage. This charge comes from the output via the feedback Thus, by minimizing the capacitor size based on necessary low frequency response, turn-on time can be minimized. A small value of Ci (in the range of 0.1µF to 0.39µF), is recommended. USING EXTERNAL POWERED SPEAKERS The LM4910 is designed specifically for headphone opera- tion. Often the headphone output of a device will be used to drive external powered speakers. The LM4910 has a differ- ential output to eliminate the output coupling capacitors. The result is a headphone jack sleeve that is connected to V O3 instead of GND. For powered speakers that are designed to have single-ended signals at the input, the click and pop circuitry will not be able to eliminate the turn-on/turn-off click and pop. Unless the inputs to the powered speakers are fully differential the turn-on/turn-off click and pop will be very large. AUDIO POWER AMPLIFIER DESIGN A 30mW/32 Ω Audio Amplifier Given: Power Output 30mWrms Load Impedance 32 Ω Input Level 1Vrms Input Impedance 20k Ω A designer must first determine the minimum supply rail to obtain the specified output power. By extrapolating from the Output Power vs Supply Voltage graphs in the Typical Per- formance Characteristics section, the supply rail can be easily found. Since 3.3V is a standard supply voltage in most applications, it is chosen for the supply rail in this example. Extra supply voltage creates headroom that allows the LM4910 to repro- duce peaks in excess of 30mW without producing audible distortion. At this time, the designer must make sure that the power supply choice along with the output impedance does no violate the conditions explained in the Power Dissipa- tion section. Once the power dissipation equations have been addressed, the required differential gain can be determined from Equa- tion 2. (2) www.national.com 11 |
Número de pieza similar - LM4910MA |
|
Descripción similar - LM4910MA |
|
|
|
Enlace URL |
| Política de Privacidad |
| ALLDATASHEET.ES |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Spanish ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
