ADT7476_16 datasheet(9/68 Pages) ONSEMI

No. de pieza	ADT7476

Descripción Electrónicos	Remote Thermal Controller and Voltage Monitor

Download	68 Pages

Scroll/Zoom	100%

Fabricante Electrónico	ONSEMI [ON Semiconductor]

Página de inicio	http://www.onsemi.com

Logo

9 / 68 page

ADT7476

www.onsemi.com

9

Serial Bus Interface

Control of the ADT7476 is carried out using the serial

system management bus (SMBus). The ADT7476 is

connected to this bus as a slave device, under the control of

a master controller. The ADT7476 has a 7-bit serial bus

address. When the device is powered up with Pin 13

(PWM3/ADDREN) high, the ADT7476 has a default

SMBus address of 0101110 or 0x2E. The read/write bit must

be added to get the 8-bit address. If more than one ADT7476

is to be used in a system, each ADT7476 is placed in ADDR

SELECT mode by strapping Pin 13 low on powerup. The

logic state of Pin 14 then determines the device’s SMBus

address. The logic of these pins is sampled on powerup.

The device address is sampled on powerup and latched on

the first valid SMBus transaction, more precisely on the

low-to-high transition at the beginning of the eighth SCL

pulse, when the serial bus address byte matches the selected

slave address. The selected slave address is chosen using the

ADDREN pin/ADDR SELECT pin. Any attempted

changes in the address have no effect after this.

Table 5. HARDWIRING THE ADT7476 SMBUS

DEVICE ADDRESS

Pin 13 State

Pin 14 State

Address

0

Low (10 k

W to GND)

0101100 (0x2C)

0

High (10 k

W Pullup)

0101101 (0x2D)

1

Don’t Care

0101110 (0x2E)

Figure 14. Default SMBus Address = 0x2E

ADDR SELECT

ADT7476

14

13

PWM3/

ADDREN

10 k

W

ADDRESS = 0x2E

VCC

Figure 15. SMBus Address = 0x2C (Pin 14 = 0)

ADDR SELECT

ADT7476

14

13

PWM3/

ADDREN

10 k

W

ADDRESS = 0x2C

Figure 16. SMBus Address = 0x2D (Pin 14 = 1)

ADDR SELECT

ADT7476

14

13

PWM3/

ADDR_EN

10 k

W

ADDRESS = 0x2D

VCC

Figure 17. Unpredictable SMBus Address if Pin 13

is Unconnected

DO NOT LEAVE ADDREN

UNCONNECTED! CAN CAUSE

UNPREDICTABLE ADDRESSES.

NOTE THAT IF THE ADT7476 IS PLACED INTO ADDR SELECT

MODE, PINS 13 AND 14 CANNOT BE USED AS THE ALTERNATE

FUNCTIONS (PWM3, TACH4/THERM) UNLESS THE CORRECT

CIRCUIT IS MUXED IN AT THE CORRECT TIME OR DESIGNED

TO HANDLE THESE DUAL FUNCTIONS.

CARE SHOULD BE TAKEN TO ENSURE THAT PIN 13

(PWM3/ADDREN) IS EITHER TIED HIGH OR LOW. LEAVING

PIN 13 FLOATING COULD CAUSE THE ADT7476 TO POWER UP

WITH AN UNEXPECTED ADDRESS.

ADDR SELECT

ADT7476

14

13

PWM3/

ADDREN

10 k

W

VCC

NC

The ability to make hardwired changes to the SMBus

slave address allows the user to avoid conflicts with other

devices sharing the same serial bus, for example, if more

than one ADT7476 is used in a system.

The serial bus protocol operates as follows:

1. The master initiates data transfer by establishing a

start condition, which is defined as a high-to-low

transition on the serial data line SDA while the

serial clock line SCL remains high. This indicates

that an address/data stream follows. All slave

peripherals connected to the serial bus respond to

the start condition and shift in the next eight bits,

consisting of a 7-bit address (MSB first), plus a

R/W bit, which determine the direction of the data

transfer, that is, whether data is written to or read

from the slave device.

The peripheral whose address corresponds to the

transmitted address responds by pulling the data

line low during the low period before the ninth

clock pulse, known as the acknowledge bit. All

other devices on the bus now remain idle while the

selected device waits for data to be read from or

written to it. If the R/W bit is a 0, the master writes

to the slave device. If the R/W bit is a 1, the master

reads from the slave device.

2. Data is sent over the serial bus in sequences of nine

clock pulses, eight bits of data followed by an

acknowledge bit from the slave device. Transitions

on the data line must occur during the low period of

the clock signal and remain stable during the high

period. A low-to-high transition, when the clock is

high, can be interpreted as a stop signal. The

number of data bytes transmitted over the serial bus

in a single read or write operation is limited only by

what the master and slave devices can handle.

3. When all data bytes have been read or written, stop

conditions are established. In write mode, the

master pulls the data line high during the 10th clock

Número de pieza similar - ADT7476_16

Fabricante Electrónico	No. de pieza	Datasheet	Descripción Electrónicos
Analog Devices	ADT7476A	1Mb / 72P	dBCool Remote Thermal Controller and Voltage Monitor REV. 0
ON Semiconductor	ADT7476A	613Kb / 67P	dBCOOL Remote Thermal Controller and Voltage Monitor May, 2010 ??Rev. 3
ON Semiconductor	ADT7476A	541Kb / 69P	Remote Thermal Controller and Voltage Monitor February, 2016 ??Rev. 7
Analog Devices	ADT7476AARQZ	1Mb / 72P	dBCool Remote Thermal Controller and Voltage Monitor REV. 0
ON Semiconductor	ADT7476AARQZ	613Kb / 67P	dBCOOL Remote Thermal Controller and Voltage Monitor May, 2010 ??Rev. 3

More results

Descripción similar - ADT7476_16

Fabricante Electrónico	No. de pieza	Datasheet	Descripción Electrónicos
ON Semiconductor	ADT7476A	541Kb / 69P	Remote Thermal Controller and Voltage Monitor February, 2016 ??Rev. 7
ON Semiconductor	ADT7463	732Kb / 50P	Remote Thermal Controller and Voltage Monitor May, 2013 ??Rev. 7
Analog Devices	ADT7476	1Mb / 72P	dBCool Remote Thermal Controller and Voltage Monitor REV. A
Analog Devices	ADT7468	1,021Kb / 80P	dBCool??Remote Thermal Controller and Voltage Monitor REV. 0
ON Semiconductor	ADT7476A	613Kb / 67P	dBCOOL Remote Thermal Controller and Voltage Monitor May, 2010 ??Rev. 3
	ADM1027	1Mb / 56P	dBCOOL??Remote Thermal Controller and Voltage Monitor May 2010 - Rev. 3
	ADT7466	691Kb / 48P	dBCool짰 Remote Thermal Controller and Voltage Monitor May 2010 ??Rev. 3
	ADT7468	1Mb / 81P	dBCool짰 Remote Thermal Controller and Voltage Monitor May 2010 ??Rev. 3
	ADT7476	620Kb / 67P	dBCOOL Remote Thermal Controller and Voltage Monitor May, 2010 ??Rev. 6
Analog Devices	ADT7466	1Mb / 48P	dBCool Remote Thermal Controller and Voltage Monitor REV. 0

More results

ADT7476 Datasheet(PDF) 9 Page - ON Semiconductor

ADT7476 Datasheet(HTML) 9 Page - ON Semiconductor

Número de pieza similar - ADT7476_16

Descripción similar - ADT7476_16

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

Datasheet Descarga

Enlace URL