Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
TPS79425DCQ Datasheet(PDF) 11 Page - Texas Instruments |
|
|
TPS79425DCQ Datasheet(HTML) 11 Page - Texas Instruments |
11 / 15 page www.ti.com Programming the TPS79401 Adjustable LDO Regulator V OUT + V REF 1 ) R1 R2 (3) R1 + V OUT V REF * 1 R2 (4) C1 + (3 x 10–7) x (R1 ) R2) (R1 x R2) (5) 22 pF 15 pF 15 pF OUTPUT VOLTAGE PROGRAMMING GUIDE OUTPUT VOLTAGE R1 R2 2.5 V 3.3 V 3.6 V C1 31.6 k Ω 49.9 k Ω 59 k Ω 30.1 k Ω 30.1 k Ω 30.1 k Ω † Not Available on the DCQ package. TPS794xx GND NR FB IN OUT EN V IN V OUT R1 C1 R2 1 µF 2.2 µF 0.01 µF Regulator Protection TPS79401, TPS79418 TPS79425, TPS79428 TPS79430, TPS79433 SLVS349D – NOVEMBER 2001 – REVISED OCTOBER 2004 The output voltage of the TPS79401 adjustable regulator is programmed using an external resistor divider as shown in Figure 24. The output voltage is calculated using: where: • VREF = 1.2246 V typ (the internal reference voltage). Resistors R1 and R2 should be chosen for approximately 40-µA divider current. Lower value resistors can be used for improved noise performance, but the device wastes more power. Higher values should be avoided as leakage current at FB increases the output voltage error. The recommended design procedure is to choose R2 = 30.1 k Ω to set the divider current at 40 µA, C1 = 15 pF for stability, and then calculate R1 using: In order to improve the stability of the adjustable version, it is suggested that a small compensation capacitor be placed between OUT and FB. For voltages < 1.8 V, the value of this capacitor should be 100 pF. For voltages > 1.8 V, the approximate value of this capacitor can be calculated as: The suggested value of this capacitor for several resistor ratios is shown in the table below. If this capacitor is not used (such as in a unity-gain configuration) or if an output voltage < 1.8 V is chosen, then the minimum recommended output capacitor is 4.7 µF instead of 2.2 µF. Figure 24. TPS79401 Adjustable LDO Regulator Programming The TPS794xx PMOS-pass transistor has a built-in back diode that conducts reverse current when the input voltage drops below the output voltage (e.g., during power-down). Current is conducted from the output to the input and is not internally limited. If extended reverse voltage operation is anticipated, external limiting might be appropriate. The TPS794xx features internal current limiting and thermal protection. During normal operation, the TPS794xx limits output current to approximately 925 mA. When current limiting engages, the output voltage scales back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be taken not to exceed the power dissipation ratings of the package or the absolute maximum voltage rating of the device. If the temperature of the device exceeds approximately 165 °C, thermal-protection circuitry shuts it down. Once the device has cooled down to below approximately 140 °C, regulator operation resumes. 11 |
Número de pieza similar - TPS79425DCQ |
|
Descripción similar - TPS79425DCQ |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |