Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
LM2623ALDX Datasheet(PDF) 9 Page - National Semiconductor (TI) |
|
|
LM2623ALDX Datasheet(HTML) 9 Page - National Semiconductor (TI) |
9 / 11 page Design Procedure NON-LINEAR EFFECT The LM2623 is very similar to the LM2621. The LM2623 is based on the LM2621, except for the fact that the LM2623 takes advantage of a non-linear effect that allows for the duty cycle to be programmable. The C3 capacitor is used to dump charge on the FREQ pin in order to manipulate the duty cycle of the internal oscillator. The part is being tricked to behave in a certain manner, in the effort to make this Pulse Frequency Modulated (PFM) boost switching regulator be- have as a Pulse Width Modulated (PWM) boost switching regulator. CHOOSING THE CORRECT C3 CAPACITOR The C3 capacitor allows for the duty cycle of the internal oscillator to be programmable. Choosing the correct C3 capacitor to get the appropriate duty cycle for a particular application circuit is a trial and error process. The non-linear effect that C3 produces is dependent on the input voltage and output voltage values. The correct C3 capacitor for particular input and output voltage values cannot be calcu- lated. Choosing the correct C3 capacitance is best done by trial and error, in conjunction with the checking of the induc- tor peak current to make sure your not too close to the current limit of the device. As the C3 capacitor value in- creases, so does the duty cycle. And conversely as the C3 capacitor value decreases, the duty cycle decreases. An incorrect choice of the C3 capacitor can result in the part prematurely tripping the current limit and/or double pulsing, which could lead to the output voltage not being stable. SETTING THE OUTPUT VOLTAGE The output voltage of the step-up regulator can be set by connecting a feedback resistive divider made of R F1 and R F2. The resistor values are selected as follows: R F2 =RF1 /[(VOUT/ 1.24) −1] A value of 50k to 100k is suggested for Rf2. Then, Rf1 can be selected using the above equation. V DD SUPPLY A Vdd supply of 3 to 5 volts is recommended for the LM2623. This voltage can be bootstrapped from a much lower input voltage by simply connecting the V DD pin to VOUT.Inthe event that the V DD supply voltage is not a low ripple voltage source (less than 200 millivolts), it may be advisable to use an RC filter to clean it up. Excessive ripple on V DD may reduce the efficiency. SETTING THE SWITCHING FREQUENCY The switching frequency of the oscillator is selected by choosing an external resistor (R3) connected between V IN and the FREQ pin. See the graph titled "Frequency vs V IN“in the Typical Performance Characteristics section of the data sheet for choosing the R3 value to achieve the desired switching frequency. A high switching frequency allows the use of very small surface mount inductors and capacitors and results in a very small solution size. A switching fre- quency between 300kHz and 2MHz is recommended. OUTPUT DIODE SELECTION A Schottky diode should be used for the output diode. The forward current rating of the diode should be higher than the peak input current, and the reverse voltage rating must be higher than the output voltage. Do not use ordinary rectifier diodes, since slow switching speeds and long recovery times cause the efficiency and the load regulation to suffer. Table 1 shows a list of the diode manufacturers. LLP PACKAGE DEVICES The LM2623 is offered in the 14 lead LLP surface mount package to allow for increased power dissipation compared to the MSOP-8. For details of the thermal performance as well as mounting and soldering specifications, refer to Ap- plication Note AN-1187. TABLE 1. Suggested Manufacturers List Inductors Capacitors Diodes Coilcraft Tel: (800) 322-2645 Fax: (708) 639-1469 Sprague/ Vishay Tel: (207) 324-4140 Fax: (207) 324-7223 Motorola Tel: (800) 521-6274 Fax: (602) 244-6609 Coiltronics Tel: (407) 241-7876 Fax: (407) 241-9339 Kemet Tel: (864) 963-6300 Fax: (864) 963-6521 International Rectifier (IR) Tel: (310) 322-3331 Fax: (310) 322-3332 Pulse Engineering Tel: (619) 674-8100 Fax: (619) 674-8262 Nichicon Tel: (847) 843-7500 Fax: (847) 843-2798 General Semiconductor Tel: (516) 847-3222 Fax: (516) 847-3150 www.national.com 9 |
Número de pieza similar - LM2623ALDX |
|
Descripción similar - LM2623ALDX |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |