Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
3-1393817-3 Datasheet(PDF) 4 Page - TE Connectivity Ltd |
|
3-1393817-3 Datasheet(HTML) 4 Page - TE Connectivity Ltd |
4 / 5 page 04-2011, Rev. 0411 www.te.com © 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Datasheets, product data, ‘Definitions’ sec- tion, application notes and all specifications are subject to change. 4 AXICOM Signal Relays Cradle P Relay V23003 (Continued) 108-98012 Rev. C All specifications subject to change. Consult Tyco Electronics for latest specifications. 9 of 14 Telecom-, Signal and RF Relays Cradle Relay P V23003 AXICOM Instructions for Impulse Operation Cradle relay P is primarily intended for impulse operation. The maximum voltage stated in the table (page 2) can be increased for impulse operation as follows: UII Impuls = UII tamb . q UII tamb = Maximum continuous voltage at ambient temperature t amb q = Factor The impulse voltage must not exceed 80% of the test voltage (winding/frame or winding/winding) or 3.3 times at ambient temperature = 20 °C and 2.3 times at ambient temperature < 20 °C the value of the maximum voltage listed in the table (page 2). Ift ED ≤ 3 s then q = Ift ED = Pulse width t2 = Cycle time If tED = > 3 s the value of q must be obtained from the nomograph (cradle relay N datasheet page 103). Examples of various periodic pulse trains (energizing side) 1. Periodic recurrence of one energizing pulse tED = tI + tII tI = Pulse width of the positive pulse at the start of the winding tI + tII = Pulse width of the negative pulse at the start of the winding tI + tII = Pulse widths within one cycle 2. Periodic recurrence of two unequal energizing pulses Instructions for Impulse Operation Cradle relay P is primarily intended for impulse operation. The maximum voltage stated in the coil table can be increased for impulse operation as follows: UII Impuls UII tambxq UII tamb Maximum continuous voltage at ambient temperature tamb q Factor The impulse voltage must not exceed 80% of the test voltage (winding/ frame or winding/winding) or 3.3 times at ambient temperature 20°C and 2.3 times at ambient temperature <20°C the value of the maximum voltage listed in the coil table. IftED ≤ 3s then q= ; IftED = Pulse width, t2 = Cycle time. If tED > 3s the value of q must be obtained from the nomograph. Examples of various periodic pulse trains (energizing side) 1. Periodic recurrence of one energizing pulse tED = tI + tII tl = Pulse width of the positive pulse at the start of the winding tII = Pulse width of the negative pulsee at the start of the winding tI + tII = Pulse widths within one cycle 2. Periodic recurrence of two unequal energizing pulses 108-98012 Rev. C All specifications subject to change. Consult Tyco Electronics for latest specifications. 9 of 14 Telecom-, Signal and RF Relays Cradle Relay P V23003 AXICOM Instructions for Impulse Operation Cradle relay P is primarily intended for impulse operation. The maximum voltage stated in the table (page 2) can be increased for impulse operation as follows: UII Impuls = UII tamb . q UII tamb = Maximum continuous voltage at ambient temperature t amb q = Factor The impulse voltage must not exceed 80% of the test voltage (winding/frame or winding/winding) or 3.3 times at ambient temperature = 20 °C and 2.3 times at ambient temperature < 20 °C the value of the maximum voltage listed in the table (page 2). Ift ED ≤ 3 s then q = Ift ED = Pulse width t2 = Cycle time If tED = > 3 s the value of q must be obtained from the nomograph (cradle relay N datasheet page 103). Examples of various periodic pulse trains (energizing side) 1. Periodic recurrence of one energizing pulse tED = tI + tII tI = Pulse width of the positive pulse at the start of the winding tI + tII = Pulse width of the negative pulse at the start of the winding tI + tII = Pulse widths within one cycle 2. Periodic recurrence of two unequal energizing pulses Product code structure Typical product code V23003 -B0 037 -F1 04 Type V23003 Cradle P Relay, dust protected Size A0 Size I, dust-protected B0 Size II, dust-protected Coils Coil code: please refer to coil versions table Contact style B1 Single contacts B6 Single contacts F1 Single contacts C1 Bifurcated contacts C4 Bifurcated contacts Contact arrangement 04 2 form C, 2 CO 05 2 form A, 1 NO 06 1 form A+ 1 form B, 1 NO+ 1 NC 10 4 form C, 4 CO Other types on request |
Número de pieza similar - 3-1393817-3 |
|
Descripción similar - 3-1393817-3 |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |