Motor de Búsqueda de Datasheet de Componentes Electrónicos
Selected language     Spanish  ▼

Delete All
ON OFF
ALLDATASHEET.ES

X  

Preview PDF Download HTML

408-10266 Datasheet(PDF) 1 Page - Tyco Electronics

No. de Pieza. 408-10266
Descripción  Insert the shank of the nest into the yoke and tighten the set screw.
Descarga  6 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Fabricante  MACOM [Tyco Electronics]
Página de inicio  http://www.macom.com
Logo 

408-10266 Datasheet(HTML) 1 Page - Tyco Electronics

   
Zoom Inzoom in Zoom Outzoom out
 1 / 6 page
background image
Instruction Sheet
PIDG* Terminal
Crimping Die
408-10266
LOC B
1 of 6
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
27 Jan 09 Rev A
2063361-1
Figure 1
Moving Die
Color-Code
Stationary Die
Locator
1. INTRODUCTION (Figure 1)
This instruction sheet provides application
instructions, maintenance, and inspection procedures
for PIDG Terminal Crimping Die 2063361–1 used in
Battery Tool 1901343–[ ]. This die will crimp PIDG
Terminals with a wire size range of 12–10 AWG.
Basic instructions on the use of this die, die
adjustments, wire preparation, etc. are provided in
Section 2, INSTRUCTIONS.
Section 3, MAINTENANCE and INSPECTION
PROCEDURES enables you to establish and
maintain a die certification program.
The die is coated with oil to prevent rust and
corrosion. With this oil from the dies, particularly from
the crimping area. Instructions for the Battery Tool
1901343–[ ] are found in Instruction Sheet
408–10070.
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures and
illustrations are for reference only and are not
drawn to scale.
2. INSTRUCTIONS
2.1. Die Insertion
1. Pivot the latch arm away from the yoke to open
the crimping head.
2. Loosen the set screw in the yoke.
3. Insert the shank of the nest into the yoke and
tighten the set screw.
4. Extend the ram until the set screw is visible.
5. Loosen the set screw in the ram.
6. Insert the shank of the indenter into the ram and
tighten the set screw.
7. Return the ram to the down position.
8. Pivot the latch arm and yoke toward each other
until the locking flange secures the latch arm to the
yoke.
2.2. Die Removal
1. Pivot the latch arm away from the yoke to open
the head.
2. Loosen the set screw in the yoke and remove
the nest.
3. Raise the ram to
“full–up” position.
4. Loosen the set screw in the ram and remove the
indenter.
2.3. Wire Stripping and Crimping Procedure
A. Wire Stripping
Strip the wires to the dimensions provided in Figure 2.
Refer to Paragraph 2.4 for die insulation crimp
adjustment.
B. Crimping Procedure
Avoid personal injury. When operation the tool,
exercise caution while holding terminals or wire
near the crimping area.
1. Select the proper terminal for the wire to be
crimped.
2. Place the terminal in the stationary die as shown
in Figure 3.
Dies will not accommodate terminals with tongue
widths exceeding 11.91 mm [.469 in.].
NOTE
i
NOTE
i
DANGER
NOTE
i


Html Pages

1  2  3  4  5  6 


Datasheet Download




Enlace URL




Privacy Policy
ALLDATASHEET.ES
Does ALLDATASHEET help your business so far?  [ DONATE ]  

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Favorito   |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn