Motor de Búsqueda de Datasheet de Componentes Electrónicos
Selected language     Spanish  ▼

Delete All
ON OFF
ALLDATASHEET.ES

X  

Preview PDF Download HTML

408-10266 Datasheet(PDF) 2 Page - Tyco Electronics

No. de Pieza. 408-10266
Descripción  Insert the shank of the nest into the yoke and tighten the set screw.
Descarga  6 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Fabricante  MACOM [Tyco Electronics]
Página de inicio  http://www.macom.com
Logo 

408-10266 Datasheet(HTML) 2 Page - Tyco Electronics

   
Zoom Inzoom in Zoom Outzoom out
 2 / 6 page
background image
408-10266
PIDG Terminal Crimping Die 2063361-1
Rev A
2 of 6
Tyco Electronics Corporation
PIDG Terminal and Splice and
PLASTI-GRIP* Terminal
C
B
A" Equals Strip Length
B" Equals Wire Barrel
C" Equals Insulation Barrel
Finished Crimp
Crimp Dot
Code
A
C
B
A
WIRE SIZE (AWG)
COLOR
CRIMP
WIRE STRIP LENGTH
DIE ASSEMBLY
WIRE SIZE (AWG)
RANGE
COLOR
CODE
CRIMP
DOT
CODE
TERMINAL
SPLICE
RANGE
CODE
CODE
MIN
MAX
MIN
MAX
2063361-1
12-10
Yellow
1
7.95 [.313]
8.74 [.344]
8.74 [.344]
9.52 [.375]
PIDG Insulation Restricting Nylon Terminal
C
B
Finished Crimp
Crimp Dot
Code
3 Equally Spaced Color Stripes
Insulation
A" Equals Strip Length
B" Equals Wire Barrel
C" Equals Insulation Barrel
A
WIRE
COLOR
CRIMP
TERMINAL
WIRE STRIP LENGTH
DIE ASSEMBLY
SIZE (AWG)
INSULATION
DIAMETER RANGE
COLOR
CODE
DOT
CODE
INSULATION
COLOR STRIPE
MIN
MAX
2063361 1
12
2.41-5.08 [.095-.200]
Yellow
1
Yellow
9 52 [ 375]
10 31 [ 406]
2063361-1
10
3.02-5.08 [.119-.200]
Yellow
1
Brown
9.52 [.375]
10.31 [.406]
Figure 2
3. Jog the ram by pulsing the trigger until the
moving die retains, but does not deform the
terminal.
4. Insert a stripped wire into the terminal until the
wire butts against the locator.
Do not turn or twist the wire or terminal during
insertion.
5. Hold the wire in place while activating the tool to
complete the crimp.
6. The ram should automatically retract when the
crimping cycle is complete. The terminal can be
removed after the ram has retracted.
2.4. Insulation Crimp Adjustment
1. The insulation crimping section of the moving
die has three crimp positions: 1–Tight, 2–Medium,
and 3–Loose.
2. Turn both insulation crimp adjustment spacers
so that they fit into the notch in the side of the die.
See Figure 1. This is the No. 3 or loose position.
(The insulation crimper screw must be loosened to
make this adjustment.)
3. Turn the insulation crimper screw enough to
hold the die firmly in place. The insulation crimper
screw will be tightened after completing steps 5
and 6.
4. Insert the
unstripped wire into ONLY the
insulation barrel position of the terminal.
5. Make a test crimp (refer to Paragraph 2.3.B for
crimping procedure). Close the die on the terminal
and hold the die in the bottomed position. Tighten
the insulation crimper screw while the dies are
bottomed, then complete the crimping cycle.
6. Remove the terminal from the dies, and check
the insulation grip as follows: bend the wire back
and force once. The terminal sleeve should retain
the grip on the wire insulation.
7. If the wire pulls out, use the following procedure
to set the insulation crimp adjustment to the next
tighter position:
(a) First, loosen the insulation crimper screw.
NOTE
i


Html Pages

1  2  3  4  5  6 


Datasheet Download




Enlace URL




Privacy Policy
ALLDATASHEET.ES
Does ALLDATASHEET help your business so far?  [ DONATE ]  

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Favorito   |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn