Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
LM9011M Datasheet(PDF) 4 Page - National Semiconductor (TI) |
|
|
LM9011M Datasheet(HTML) 4 Page - National Semiconductor (TI) |
4 / 16 page AC Electrical Characteristics (Continued) The following specifications apply for V CC = 5V, VS_HI =VCC,VRESET =VCC, -40˚C≤TA≤+125˚C. The AC Timing Characteristics are not production tested. Minimum and Maximum limits are guaranteed by device characterization. Symbol Parameter Conditions Minimum Maximum Units Electronic Timing Interface T DF1 Fault Delay Time Sx Output Short to Ground Fault From ENB=1to FAULT ≤ 10% C FAULT = 25pF 2 µs T DF2 Fault Delay Time Sx Output Short to Battery Fault From ENB=0to FAULT ≤ 10% C FAULT = 25pF 2 µs T TRI TRI-STATE Delay Time From RESET=0toAll Sx Outputs Off 2µs T RISE 2 Fault Pin Rise Time 10% to 90%,C FAULT = 25pF 5 µs T FF(OFF) False Fault Time From ENB=0to FAULT ≥ 90% C FAULT = 25pF C LOAD = 6.8nF, RLOAD = 10KΩ 25 µs C LOAD = 12.7nF, RLOAD = 10KΩ 30 µs T FF(ON) False Fault Time From ENB=1to FAULT ≥ 90% C FAULT = 25pF C LOAD = 6.8nF, RLOAD = 10KΩ 8µs C LOAD = 12.7, RLOAD = 10KΩ 10 µs T UDF Undefined Fault Time From ENB = 0 for 8uSec, to Valid FAULT C LOAD = 6.8nF, RLOAD = 10KΩ 20 µs C LOAD = 12.7nF, RLOAD = 10KΩ 25 µs Note 1: Absolute Maximum Ratings indicate the limits beyond which damage may occur. Note 2: ESD Ratings is with Human Body Model: 100pF discharged through a 1500 Ω resistor. Note 3: Operating ratings indicate conditions for which the device is intended to be functional, but may not meet the guaranteed specific performance limits. For guar- anteed specifications and conditions, see the Electrical Characteristics. Note 4: Tested per VR Sensor Interface test circuit. See figures 8 and 9. Note 5: Minimum Detect Current is not production tested at +85C. Specifications is guaranteed through device characterization and Test Limits at 25˚C and 125˚C. Note 6: VR Sensor Interface Tdelay, measured from VR input sine wave zero-crossing to VR_OUT going high. See figure 9. Note 7: Electronic Timing Interface Tsetup, minimum time between Vcc > 4.75V and RESET = 1. Note 8: Electronic Timing Interface Tsetup, minimum time between RESET = 1 and D0 = 1. Note 9: Electronic Timing Interface Tsetup, minimum time between D0 / D1 = valid and ENB = 1. www.national.com 4 |
Número de pieza similar - LM9011M |
|
Descripción similar - LM9011M |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |