Motor de Búsqueda de Datasheet de Componentes Electrónicos
Selected language     Spanish  ▼
Nombre de pieza
         Descripción


0-525355-8 Datasheet(Hoja de datos) 5 Page - Tyco Electronics

No. de Pieza. 0-525355-8
Descripción  Cumulative Trauma Disorders can result from the prolonged use ofmanually powered hand tools.
Descarga  7 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Fabricante  MACOM [Tyco Electronics]
Página de inicio  http://www.macom.com
Logo 

   
 5 page
background image
411- 1097
Double Action Hand Crimping Tools 525690 and 525691
5
of 7
Rev D
Tyco Electronics Corporation
5. MAINTENANCE AND INSPECTION
It is recommended that a maintenance and inspection
program be performed periodically to ensure
dependable and uniform terminations. Though
recommendations call for at least one inspection a
month, frequency of inspection depends on:
1. The care, amount of use, and handling of the
tool.
2. The presence of abnormal amounts of dust and
dirt.
3. The degree of operator skill.
4. Your own established standards.
The tool is inspected before being shipped; however,
it is recommended that the tool be inspected
immediately upon arrival to ensure that the tool has
not been damaged during shipment.
5.1. Daily Maintenance
1. Immersed the tool (handles partially closed) in a
reliable commercial degreasing compound to
remove accumulated dirt, grease, and foreign
matter. When degreasing compound is not
available, the tool may be wiped clean with a soft,
lint--free cloth. DO NOT use hard or abrasive
objects that could damage the tool.
2. Make certain that the retaining pins are in place
and that they are secured with retaining rings.
3. All pins, pivot points, and bearing surfaces
should be protected with a THIN coat of any good
SAE 20 motor oil. DO NOT oil excessively.
4. When the tool is not in use, keep the handles
closed to prevent objects from becoming lodged in
the jaws. Store the tool in a clean, dry area.
5.2. Periodic Inspection
A. Lubrication
Lubricate all pins, pivot points, and bearing surfaces
with any good SAE 20 motor oil as follows:
Tool used in daily production — daily
Tool used daily (occasional) — weekly
Tool used weekly — monthly
Wipe excess oil from the tool, particularly from the
crimping area. Oil transferred from the crimping area
onto certain terminations may affect the electrical
characteristics of an application.
B. Visual Inspection
1. Close the tool handles until the ratchet releases
and then allow them to open freely. If they do not
open quickly and fully, the spring is defective and
must be replaced. See Section 6, REPLACEMENT
AND REPAIR.
2. Inspect the head for worn, cracked, or broken
jaws. If damage is evident, return the tool for
evaluation and repair. See Section 6,
REPLACEMENT AND REPAIR
C. Gaging the Crimping Chamber
This inspection requires the use of plug gages
conforming to the dimensions provided in Figure 7.
To gage the crimping chamber, proceed as follows:
1. Remove traces of oil or dirt from the crimping
chamber and plug gage.
2. Insert each insulation crimp adjustment pin into
Position 1. See Figure 8.
NO--GO Dia
GO Dia
Jaw Closure
Configuration
SUGGESTED PLUG GAGE DESIGN
FOR WIRE BARREL SECTION
TOOL
GAGE ELEMENT DIAMETER
TOOL
GO
NO--GO
525690 2.768--2.776 [.1090--.1093] 2.918--2.921 [.1149--.1150]
525691 3.022--3.030 [.1190--.1193] 3.172--3.175 [.1249--.1250]
GO Dia
NO--GO Dia
GO
NO
GO
Jaw Closure
Configuration
W
W
SUGGESTED PLUG GAGE DESIGN
FOR INSULATION BARREL SECTION
TOOL
GAGE ELEMENT THICKNESS
TOOL
GO
NO--GO
W
525690
0.889--0.897
[.0350--.0353]
1.394--1.397
[.0549--.0550]
2.80--3.05
[.110--.120]
525691
1.143--1.151
[.0450--.0453]
1.648--1.651
[.0649--.0650]
4.50--4.75
[.177--.187]
Figure 7
3. Close the tool handles until the jaws bottom,
and hold in this position. DO NOT force beyond
initial contact.




Html Pages

1  2  3  4  5  6  7 


Datasheet Download




Enlace URL

¿ALLDATASHEET es útil para Ud.?  [ DONATE ]  

Todo acerca de Alldatasheet   |   Publicidad   |   Contáctenos   |   Política de Privacidad   |   Favorito   |   Intercambio de Enlaces   |   Lista de Fabricantes
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl