Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
TA8044AF Datasheet(PDF) 3 Page - Toshiba Semiconductor |
|
TA8044AF Datasheet(HTML) 3 Page - Toshiba Semiconductor |
3 / 10 page TA8044AF 2002-02-27 3 PIN DESCRIPTION PIN No. SYMBOL DESCRIPTION 1 VIN1 Power supply input pin for VCC1. It contains a 150mA (Typ.) current limiter. 2 VS1 Current limiter pin for VCC1. A 120mΩsense resistor is included between pin 1 and this pin. 3 OUT1 Power supply input pin for VCC1. When using an external current boost transistor, connect the base of a PNP transistor to this pin. No external transistor is required when using the IC at a load current of 10mA or less. In this case, connect the power supplies by shorting pins 1, 2, and 3. 4 VCC1 Voltage detection / output pin for VCC1. When using a current boost transistor, connect the collector of a PNP transistor to this pin. When used with a load current of 10mA or less, this pin serves as an output pin for the 3.3V power supply. 5 COMP1 Phase compensating pin for VCC1. Connect a phase compensating capacitor between pin 4 and this pin. 6 EN On / off control pin for VCC2. The 5V output is turned on when EN is high and turned off when EN is low. A 50kΩ pull-down resistor is included in GND. 7 GND Grounded 8 RESET Power-on reset / watchdog timer reset output pin. ・ Generates a reset signal that is determined by CT and RT at the TC pin. ・ If no clock is fed to the CK input, this pin generates a reset pulse intermittently. This is an NPN transistor collector output, with a 100kΩ pull-up resistor built into VCC2. 9 TC Time setup pin for the reset and watchdog timers. Connect resistor RT to VCC2 and capacitor CT to GND. 10 CK Clock input pin for the watchdog timer. If used only as a power-on reset timer, pull up this input to VCC2. 11 VCC3 This pin contains a 7.5V Zener diode. To use this pin, short it to pin 13. When the VCC2 voltage becomes abnormal, the Zener diode suppresses the voltage. 12 COMP2 Phase compensating pin for VCC2. Connect a phase compensating capacitor between pin 13 and this pin. 13 VCC2 Voltage detection pin for the 5V constant-voltage power supply, VCC2. It also supplies power to the reset timer block. 14 OUT2 This pin is used to connect the base of an external PNP transistor. The output voltage is controlled by an internal op-amp to maintain it stably at 5V. Since the recommended current of IOUT is 5mA, an output current of up to 600mA can be flowed if HFE of the external transistor is 120 or more. 15 VS2 Detection pin for the VCC2 current limiter. A voltage drop occurring in the external resistor Rs between pins 15 and 16 is monitored. The current limiter is actuated when the voltage drop exceeds 0.3V. Ex. ) When the current limiter need to be actuated at a load current of 600mA Rs = 0.3V / 600mA = 0.5Ω 16 VIN2 Power supply input pin. An internal 6V constant voltage is connected to this pin for supplying power to the VCC1 / 2 current limiters, voltage regulating circuit for VCC1, reference voltage source, and the EN input circuit. |
Número de pieza similar - TA8044AF |
|
Descripción similar - TA8044AF |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |